3:35 haha! Can related. ”Dont like this, prefer this but usually end up with this”

Great tutorial, needed to see this for my own project.

Great vid thanks

I like it thanks for the great tips 👍

Thanks for this, was really trying to figure out how to terminate baseboard where the wall met the surface of a cabinet that was flush with the wall.

To the point. I like it

Awesome work! Now I know how to end my bathroom baseboard up to the 90° tiled wall. Thank you.

@BrentDarlington

11 ай бұрын

Glad I could help!

Super helpful thank you!!!!

@BrentDarlington

Жыл бұрын

Thanks!

Great video!

@BrentDarlington

7 ай бұрын

Thanks!

Those are very easy to glue with the regular glue. All you need is a bit of painters tape.

@BrentDarlington

2 жыл бұрын

Yes

Would it be a good idea to back cut when base and casing are the same thickness?

@BrentDarlington

Жыл бұрын

I usually break the edge a bit to leave a grove where they meet.

Do you need a slide saw to do these? Mine bevels both directions but it only goes up and down.

@BrentDarlington

11 ай бұрын

You're good with the saw you have

Plinth is another option.

@BrentDarlington

3 жыл бұрын

I'm not a fan of plinth blocks but it is an option👍

The floor return with the mitre running through the board isn’t the best way to do it. You can still bring the mould around another way by measuring out. It’s a smaller joint and less to fill

@BrentDarlington

Жыл бұрын

I don't understand what you mean

What is this spray?

@BrentDarlington

Жыл бұрын

it speeds up the hold time for the CA glue

What's the size of the miter saw?

@BrentDarlington

2 жыл бұрын

12"

@reggieholguin7907

Жыл бұрын

12

I like to just cut it straight and then smear caulk all over the end of it🤷‍♂️

@BrentDarlington

3 жыл бұрын

Do your best and caulk the rest!

@mikegwin2924

Жыл бұрын

I don’t smear caulk but I do spread a light coat to seal the fibers on the MDF before applying paint.

@jamieorton5898

Жыл бұрын

😅😅 I wish i could do that🎉

It would have been nice if you had bothered to tell us what angle your cuts were and what you used spray the ends with before you glued them....I'm still in the dark!!

@BrentDarlington

2 жыл бұрын

The saw is set up at 45 degrees to make a 90 degree angle. I used Miter Bond which is a CA glue, basically super glue, on one side and the spray is an activator to speed up the set time. You can use regular wood glue and hold it for a bit or tape it with some masking tape while it dries

@Marshall1565

2 жыл бұрын

He said every angle was 45 and it’s common sense on mitres, 45 = 90, 22.5 =45

You didnt teach the 3rd on... you just did it.

@BrentDarlington

Жыл бұрын

Basically the same thing, cut at 45 degrees

MANUFACTURER AND EXPORTER [ PRODUCT INTRODUCTION] BASEBOARD/MDF WHITE MOULDING /CROWN/CASING/WAINSTCOT/QTARTERROUND ANY INTERESTING,PLEASE CONTACT US.

@BrentDarlington

2 жыл бұрын

no thanks, spammy

@MAGAMAN

2 жыл бұрын

@@BrentDarlington I'm sure that stuff will totally be OK once it arrives after being shipped from china or wherever. LOL Home depot can't even deliver this stuff a few blocks without damaging it.

Showed us absolutely nothing

@BrentDarlington

3 ай бұрын

Thanks!

You don't explain anything

No explanation as to what angle to make the cuts..be more thorough, all the detail on the camera is with the gluing!

@BrentDarlington

Жыл бұрын

45 degree. Thanks for your input, noted.