this worked for me. Thank you so much! Great information. All the details I needed. Kills me how many cartridges I've wasted in the past.

Thanks a lot brother it really worked like a charm on my Canon G3400 Series. Now it prints colour just like a brand new one. Cheeeeeers!

I must say i enjoy your natural speaking voice a ton more than the text-to-speech synth. Also i was surprised that your shipping rate to Europe is quite affordable.

@BCHTechnologies

5 жыл бұрын

Thank you!

Putting a straw on the refill hole and blowing in till ink comes out worked for me

Thank you!! I've been trying to find this info for a week... btw, LOVE y'alls refill kits

I find it easier to suck out sludge from the interior of the cartridge with a syringe and needle, than trying to suck it out through the jets. Although be careful not to puncture the filter at the bottom outlet of the cartridge. Just inject some distilled water, let it sit for hours or days and suck it back out. I also soak the outside of the head on a shallow puddle. You will really notice when you have cleared the clog as ink comes bleeding out much more freely. To inject it back in without making a total mess have a second syringe & needle with the plunger removed and inject the foamy ink into that and just let it trickle back in slow. You can remove the ink entirely or just churn it up. This method seems especially necessary of the tri-color ink for some reason: perhaps because there are little tubes running from each color to the jets that get clogged up.

Any advice when the cartridge prints ok but after a few impressions it starts to stop flowing ink?

when i was cleaning my canon pg 40 ink cartidge, a tape like thing peeled off from print head, i think that was air seal, now that portion of printhead is not printing anything, that area is just blank in print. what can i do?

Why my black ink cartridge keep giving me trouble? I fill it up again, I used the priming clip the same way I did last time but doesn't wanna work. What else can I do?

worked for me thanks man

@BCHTechnologies

2 жыл бұрын

Good to hear

method 2 is the best.

Using a vacuum cleaner? Now that really impresses me. For most of the last 10 years, I have had mixed results with Canon Cartridges (30&31). The first refill is fine. After this, attempts to do it a 3rd time always fail. I came to the conclusion Canon prevents the user from re-using a cartridge. One time I completely disconnected/removed the printer. I let it sit for more than a month figuring on getting rid of it (Meanwhile buying a tank printer). On a whim, I plugged the MP190 in and it operated like new!!! So I figured the memory died and the cartridges were reactivated. I like this printer and refuse to give it up. Now the new cartridges cost $50 for the pair. Sick.

1:00 thats like 1000 dollars in cartridges hahaha

how do you test if the electronic is still good.

@BCHTechnologies

6 жыл бұрын

Wipe the ribbon clean and dry, also make sure the pins on the printer are dry. If you repeat it few times and the printer still rejects the cartridge, then the electronic is bad. In older models, HP allows you to bypass the electronic check and print a diagnostic report. It can still print with bad electronics. However, this function was never in their manual and seemed taken away from new models.

Hello , can you suggest me from where I can get empty/used hp 62 black/tri color cartridges?

@Ed-gd5ec

2 жыл бұрын

It seems like mine was damaged little bit. The inside of the cartridge is getting solid (with lots of bubbles in it, and the printer is not printing anything) After again sucking out all the ink, I've to refill the cartridge which agains only works for about 24hrs. Again it behaves same ,the ink gets lot of bubbles just like in this video at time 6:35

@Ed-gd5ec

2 жыл бұрын

or do you any solution to that problem which is at 6:35 (lots of air bubbles forms inside the ink)

@BCHTechnologies

2 жыл бұрын

EBay, of course.

WHat worked really for me, after using a lot of tricks, as strong solvents, hot water, and ultra wave bath, blowing, aspiration, no way to see some red on the nozzle (HP443 2 years no use) WHat worked really well and fast : I put hot water in my dental jet, pressure at the max. Just one full recipe and the red was open. It may be better to do it 2 or 3 times as it is pushing into the micro holes, but it really worked, after 24 hours testing different tricks. It is not sending ink everywhere do not be afraid ;)

How to unclog Hp 920 printhead....

what's the web address

@BCHTechnologies

5 жыл бұрын

www.bchtechnologies.com

better use a duct tape rather than buying this tape..

@BCHTechnologies

6 жыл бұрын

Another option is the "Glue Dots" which you can get from OfficeDepot or 99 cents store.