24 Upgrades & Modification for my Anycubic Mega S | 3D Printing
24 Upgrades & Modification for my Anycubic Mega S.
Thanks for comment, like and subscribe my 3D printing channel.
*************************
♥ Support my Channel ♥
www.buymeacoffee.com/oppapalam
*************************
*************************
Here is the quick link for all modification CAD files :
bit.ly/3F8Frd9
*************************
FILES / STLS / IMAGES / LINKS FOR ALL UPGRADES:
Part #01 tool rig
www.thingiverse.com/thing:279...
by mjuddi
Part #02 caliper holder
www.thingiverse.com/thing:345...
by kuehmayer
Part #03 tmc2209 replacement
taobao: item.taobao.com/item.htm?spm=...
amazon: www.amazon.com/bigtreetech-pr...
Part #04 stepper fan holder
www.thingiverse.com/thing:295...
by mariusbach
Part #05 y pulley cover back cover
www.thingiverse.com/thing:460...
by oriundo
Part #06 y pulley rear cover
www.thingiverse.com/thing:425...
by ez_diy_technics
part #07 y sensor cover
www.thingiverse.com/thing:425...
by ez_diy_technics
Part #08 heated bed cable
www.thingiverse.com/thing:431...
by ro0
Part #09 waste bin
www.thingiverse.com/thing:333...
by jbrow532
Part #10 z-level screw holder
www.thingiverse.com/thing:282...
by alithing
Part #11 cable chain joint
www.thingiverse.com/thing:286...
by michelix
Part #12 cable chain
www.thingiverse.com/thing:366...
by sergiu_i
Part #13-14 led ring light & touch on-off sensor
led ring light (12v)
taobao: item.taobao.com/item.htm?spm=...
amazon: www.amazon.com/90mm-angel-eye...
touch on-off sensor
taobao: item.taobao.com/item.htm?spm=...
amazon: www.amazon.com/sensor-switch-...
Part #14 dual hotend fans (12v)
taobao: item.taobao.com/item.htm?spm=...
amazon: www.amazon.com/winsinn-coolin...
Part #15 pcb modification
ph2.0 power cable
Part #16 extruder motor fan cover
www.thingiverse.com/thing:516...
by oppapalam
Part #17 hotend cover
www.thingiverse.com/thing:516...
by oppapalam
Part #18 hotend fan cover
www.thingiverse.com/thing:516...
by oppapalam
Part #19 hotend plug cover
www.thingiverse.com/thing:417...
by xscuba360
Part #20 hotend fan airduct
www.thingiverse.com/thing:516...
by oppapalam
Part #21 bed level knob nameplate
www.thingiverse.com/thing:516...
by oppapalam
Part #22 faceplate with screen cover
www.thingiverse.com/thing:381...
by truelordchanka
Part #23 bed leveling wheel
www.thingiverse.com/thing:379...
by mach
Part #24 bed holder extended
www.thingiverse.com/thing:404...
by stonefpv
Media:
*************************
Gmail:oppapalamhello@gmail.com
KZread : / @oppapalam
Instagram : / oppapalamhello
Twitter : / oppapalam
Reddit : / oppapalam
Facebook : / oppapalamhello
Thingiverse : www.thingiverse.com/oppapalam...
Buymeacoffee : www.buymeacoffee.com/oppapalam
*************************
Пікірлер: 90
I will always find it amazing that with a 3d printer you can print stuff to upgrade it. Literally making itself better. So awesome!
@oppapalam
2 жыл бұрын
Thank you so much❗️I also like to print some toys and play with kids😄
@Pattot818
2 жыл бұрын
@@oppapalam which toys do you recomment?
@oppapalam
2 жыл бұрын
www.thingiverse.com/thing:4138701 www.thingiverse.com/thing:3223118 www.thingiverse.com/thing:1396307
Wow. You did so much. I wish I had the patience to upgrade my Mega S this much.
@oppapalam
2 жыл бұрын
Thank you so much, I have no idea when I got Mega S and I spent more than 3 months to upgrade my printer. That's why I made this video is want to share my upgrade process and everyone can do it as well.
thank you this is amazing to have for my old "legacy" mega S...
Wow, you did a good job. I like it and will try to repeat! thank you!
i bought my first 3d printer a few days ago, its a anycubic mega modded to hell, its got better motor drivers, a custom mobo, direct extruder and other stuff, must say i'm extremely happy with it and i'll def be printing some of these upgrades!
@oppapalam
2 жыл бұрын
Nice, good to see your first print stuff👍🏻
I just got an i3 Mega S and I love working on it. Thanks for the video.
@oppapalam
2 жыл бұрын
Hope you enjoy it👍🏻
Really cool! Super excited to get my Mega S and do some of these
@oppapalam
Жыл бұрын
Here is the quick link for all modification CAD files : bit.ly/3F8Frd9 Enjoy❗️
@Chroshin
Жыл бұрын
@@oppapalam thankyou!
Excellent Job!
Thank you. I have downloaded the tool rig.
bravissimo...ottimo progetto
Very Good! Like!
@oppapalam
2 жыл бұрын
Thank you so much😊
I love this brand of printer. Holy smokes it's nice
@oppapalam
2 жыл бұрын
Anycubic mega s is easily to use and well-builded machine.
Very helpful. Thank you! The exposed cables on my printer drive me crazy.
@arwing123
4 ай бұрын
You are welcome and enjoy happy printing
I am almost done but I noticed that in 7:06 you are configuring the fan for the hotend but there is no part to print for holding the fan next to the hotend? You show it but there is not a part to print? What is the size of the little fan that is attached directly to the hotend? Where are the wire connections to make it connect to the power from? They are hanging there but I don't get which wires they are?
TMC2209 driver install is the best upgrade ypu can do imo. My Mega S is almost completely silent aside from the parts cooling fan. Ive also changed all the other fans to Noctua fans.
@oppapalam
2 жыл бұрын
Yes, TMC2209 is the best upgrade and I just changed one Noctua fans on my extruder as it is quite hot when printing.
@JamShady
2 жыл бұрын
Tell us more please. How easy is it to do?
@oppapalam
2 жыл бұрын
If you are using anycubic i3 mega s, just remove previous stepper drivers and plug new stepper drivers and revert these cable connecters.
@newdimension2012
Жыл бұрын
what voltages are you runing?
Thank you
Are they compatible with anycubic mega pro? or is it necessary to scale?
how many fans did you use for this build? i only ask because not all fans are labeled, trying to figure out what fans you used for the board. the dual fans you mounted
@oppapalam
2 жыл бұрын
Thanks for your watching, 2pcs 5015 blower fan (12V) is used for the nozzle cooling. Part #14 dual hotend fans (12v) taobao: item.taobao.com/item.htm?spm=a1z0k.7386009.0.d4919233.69645f13e458z8&id=43314193976&_u=t2dmg8j26111 amazon: www.amazon.com/winsinn-cooling-50x50x15mm-extruder-makerbot/dp/b079bmx2s6/ref=sr_1_3?crid=f8jytww8i7cr&dchild=1&keywords=5015+blower+fan+12v&qid=1622446875&sprefix=12v+5015+5%2caps%2c357&sr=8-3
Woah a caliper holder, that's awesome! It'll help me clear space off my desk. Honestly I'm going to try doing most of these upgrades asap, do you have any advice for leveling the printer? I've had some ringing issues and I'm wondering if that's the cause.
@oppapalam
2 жыл бұрын
I do the bed leveling by using A4 paper at all, no more tips for leveling. If you have ringing issues, try to print it at lower speed (40~60mm/s)
@massir7769
2 жыл бұрын
@@oppapalam gotchu thanks, already printed the caliper holder and it works great. Going to start on some other upgrades.
@massir7769
2 жыл бұрын
@@oppapalam curious what benefit the PCB modification does (and what it is exactly?) As well as the added fans and hotend cover as opposed to the stock option?
@oppapalam
2 жыл бұрын
@@massir7769 Ph2.0 connector is added to the PCB which is connected to touch sensor as a power source (5V) for the light of the LED ring light. Yes, one of the added fans is opposed to the hotend cover.
Amazing quality. What 3d printnting settings do you use?
@oppapalam
2 жыл бұрын
Thank you so much! Here is the link of Cura printer setting. drive.google.com/file/d/1cA6uj6XLS9r6snIjHXhEuf31ohSF17na/view?usp=sharing
@zazuki100
2 жыл бұрын
Please show you settings about the plastic (petg?) in cura slicer
@oppapalam
2 жыл бұрын
All parts printed in PLA, resolution 0.2mm, infill 10~20%, no rafts, supports (check my thingiverse link)
Hello. Many thanks for your sharing. Are your modifications and improvements valid for the Anycubic Mega x? Cordially.
@oppapalam
2 жыл бұрын
Hi, thank you for your watching! Many of them are suitable for Mega X except the cable chain and the pulley covers.
@frabrf
2 жыл бұрын
@@oppapalam ok thanks.to other shared videos.
In part 18 Hotend Cover and Fan Cover where did you get the fan and if you printed a mold for it to be attached to the hotend?
@oppapalam
Жыл бұрын
I bought all fans from Taobao or you may try to buy it from aliexpress. Yes, I printed hotend cover and attached to the hotend. If you want a strong cover, you should print ABS as well.
The wire hanging I mentioned below is at time stamp 7:00
can you show us how to make good lapses like in the video??
Sorry what was the sensor switch called I can't find the link on Amazon. I asked before but lost your answer :)
@oppapalam
Жыл бұрын
Here are both links, hope I can help you💪🏻 RLECS 12-24V 2A Single Color Light Emitting Diode Strip Light Brightness Controller On/Off Switch Inline Tact Switch Black DC Mini LED Dimmer Touch Switch a.co/d/9J8JjE6 HKD5.57 34% Off | DC 12V 24V LED Strip Touch Dimme Brightness Control Simpl Dimmer Switch Controller for 5050 3528 2835 Light Strip Single Color a.aliexpress.com/_mNpTiCU
@Carpettrip
Жыл бұрын
@@oppapalam thank you I have it!
@Carpettrip
Жыл бұрын
@@oppapalam got it thank you!
Hi, is this Stuff also Compatible with the Mega Pro?
@oppapalam
Жыл бұрын
Yes, some stuff are compatible with Mega Pro
I can't fit my hotend cable through the chain. How did you do this
@oppapalam
Жыл бұрын
Here is the link for the 10x20 cable chain and print the file named AI3M_complete_chain_V3.stl which is easy to pass through the cable socket easily. www.thingiverse.com/thing:3668667
Hello! quick question: is it ok to print the hotend cover with PLA?
@oppapalam
2 жыл бұрын
Hi Eugen, it is good if you keep printing PLA as well. On the other hand, it should be printed by ABS if you will print ABS with enclosure.
@meltiseugen
2 жыл бұрын
@@oppapalam I only print PLA :D Two more things I'm curious about: How exactly did you place the hotend fan inside the case (it's not really visible in the video)? Also, I saw that you placed two part cooling fans on the same wire, is it safe to do so? Will it impact the performance of the fans? I want to do the exact same thing, and this is the only video I found that has this. I want to say that this is the coolest video I've seen about upgrades for anycubic printer and I really appreciate the work you've put into this video, cheers. :D
@oppapalam
2 жыл бұрын
Thanks for your watching and hope you enjoy my video😊 1. Hotend fan is clamped heat sink easily www.amazon.eg/-/en/distance-J-head-Cooling-thermistor-Printer/dp/B0968ZR9JX/ref=sr_1_1?crid=13PHIDN2TE38L&keywords=e3d+v5+hotend+fan&qid=1648485928&sprefix=e3d+v5+hotend+fan%2Caps%2C216&sr=8-1 2. Both part cooling fans are connected in parallel that means both fans keep using 12V kzread.info/dash/bejne/Y4OBs65xiMWfo5s.html
@meltiseugen
2 жыл бұрын
@@oppapalam part cooling fans are connected in parallel, but they both are connected to the same socket on the PCB, right?
@oppapalam
2 жыл бұрын
Yes, correct
支持~~
@fullydimension
2 жыл бұрын
睇哂,好有心機~~
@oppapalam
2 жыл бұрын
多謝支持,我都有睇你的影片架👍🏻
@fullydimension
2 жыл бұрын
@@oppapalam 出年「再」出發
the fan attachment at 7:24 is not available for printing?
@oppapalam
Жыл бұрын
Hi Jeff, the blue fan case is bought, here is the reference link : a.aliexpress.com/_mPibgja, you should choose bracket for V5 and 12V
@Carpettrip
Жыл бұрын
@@oppapalam thank you so very much!
@oppapalam
Жыл бұрын
You are welcome👍🏻
Some of your upgrades there is no thingiverse number, can you provide the files? Thank you
@oppapalam
Жыл бұрын
Thingiverse number can be found in the file link. Here is the quick link for all modification CAD files : bit.ly/3F8Frd9 Enjoy your upgrades‼️
@taurus533
Жыл бұрын
@@oppapalam are these all the prints in your video, example which way to turn knobs to level bed? Thank you again. Much appreciated 👍🏾🙏🏾
@taurus533
Жыл бұрын
@@oppapalam sorry to bother you....printed out your mods and for the links (cable chain) it cannot connect to the pieces that would attach to the printer....please can you assist? Thank you
@oppapalam
Жыл бұрын
@@taurus533 As I remember, cable chain and joint are not 100% fitted, so you have to cut out a little bit or use air dryer to heat up the joint before assembling the cable chain
@AksenDik
Жыл бұрын
@@oppapalam width of hotend chain is 25.8 mm, but model “AI3M_Schleppkette_B” is 28.5mm. It’s not connect
part#20 link is failed . How to get the part#20 stl?
@oppapalam
7 ай бұрын
Here is the quick link for all modification CAD files : bit.ly/3F8Frd9
Sorry, but this video ist to fast for 24 Upgrades...
@Carpettrip
Жыл бұрын
you can play it at 0.25 speed in KZread and stop it when you want
竟然係廣東話
@oppapalam
2 жыл бұрын
將會用廣東話繼續出新片,希望多多支持💪🏻💪🏻💪🏻
so, it you have no idea what to do with a 3d printer - mod a printer itself.. I did only those which are really necessary upgrades: 1. motor drivers strongly increase a comfort, 2. heatbed cable holder, preventing its move on a heatbed side (no chain, just a small part which fixing a cable and not allow the cable to break at the weakest point - solder spots), 3. rewiring the heater of the hotend with 2 thick cables, going straight from the heater to the motherboard - no connectors at all!!! Original cable and connectorssss placement is awfully designed. If you have "t0 sensor" problem - 90% chance it is the cable or the connector. 9% - wire connection on a motherboard is loose, or right this connector soldering points broke. The cable to the hotend consists of 14 thin wires, whereas only 6 or 7 are needed, two of which should be at least a 1mm thick. Instead - 14 useless thin wires and a connector that get loose constantly becaus eof the movement, stopping long prints. 4. hotbed isolation mat. reduces power consumption, the bed heats faster. 5. probably another cooling duct. I cant say it changes the world, but sometimes prints are looking better.
Folks...I am stunned how almost no one is commenting on how terrible the print quality is on every part shown. Absolute beginner garbage with most every flaw you can name...stringing, layer lines, banding, elephants foot...etc. These prints are absolute garbage. The designs...awesome. But who shows garbage quality prints like this in a tutorial?!?
@oppapalam
9 ай бұрын
I understand your frustration with the print quality displayed in the tutorial. It can be disappointing to see subpar results, especially when the designs themselves are impressive. While it's important to acknowledge the flaws in the prints, it's also worth considering a few factors that might contribute to the situation. Firstly, tutorials often aim to showcase the design process or specific techniques rather than focusing solely on achieving flawless prints. The primary purpose might be to teach design principles or demonstrate a particular workflow, with print quality being a secondary concern. Additionally, printing quality can be influenced by various factors, including the printer settings, filament type and quality, environmental conditions, and even the skill level of the person operating the printer. Beginners, in particular, may encounter challenges in achieving optimal print quality due to their limited experience. Constructive feedback regarding print quality is valuable, as it helps both the tutorial creator and other viewers understand the areas that need improvement. It's possible that the tutorial creator may appreciate such feedback and make adjustments in future tutorials to address these concerns. Remember that the learning process often involves trial and error, and it may take time to refine one's skills and achieve better print quality. By providing feedback and expressing your expectations, you can contribute to the growth and improvement of the tutorial content.