Nice tutorial!!! Kawasaki factory instructions are always fun!

Thank you, just ordered a kit.

Just cool to see someone else in Michigan that went through hoffer performance.

@NoBSZone

4 ай бұрын

Been working with him closely for good 15 years.

I used your video to help me install instead of the instructions lol. But I dropped the washer down into my bike and almost the plastic piece but I held onto it! Lol. Rip washer

@40thzx6

4 ай бұрын

lmao ill pray u find it😂😂

Top!!!!!

Awesome thank you!

@NoBSZone

2 ай бұрын

You bet!

My instructions say the washer goes under the end of the damper connected to the handle bars, the plastic washer and collar go under the center damper on the bracket to the gas tank. Tightened to 97 inch lbs

thanks for the amazing video, would you please elaborate on which RAM mount that is fit the (MA RAM Mount) mentioned please?

I have the 2013 zx6r along with yss steering damper, I’m not sure if it use m6 or m8 bolt (along with the thread length - i dont know the required length) on the damper clamp to install quadlock phone mount.

I added the GPR Steering Damper V5. I think it looks clean compared to a rod on there, IMO. I added to both my ZX6R and ZX10R ( took off electronic dampner to add the GPR V5.)

@NoBSZone

Жыл бұрын

Yea, GPR makes good stuff!

@rogervega9846

Жыл бұрын

I assume you had to either slice a piece of the key in order to get clearance w/ the GPR? Or did you purchase the entire kit that includes the GPR clip on kit?

Thanks for the detailed video brother. I will have my kit within few days. Can you suggest setting(s)/number on damper now that you have had some time riding with damper kit. Thanks

@NoBSZone

8 ай бұрын

Really depends on the road and pace. Put in middle go from there.

Went with this version. Cleaner install and looks better.

@NoBSZone

Жыл бұрын

Totally agree

Just installed this exact one on my 2024. Couldn’t help but notice my instructions say to use the washer for the other bolt connecting to the bracket. So just the collars on the center and the washer for the other T40 bolt. Might want to check yours.

@NoBSZone

7 ай бұрын

I just looked at the one on my zx10r and did it same as was sent from kawi. Good looking. Thanks

Hi mates. May I know the model type of Ohlins like your video? Part code or model name maybe help.. Thanks

Can you post a video on your experience riding with the damper installed?

@NoBSZone

Жыл бұрын

I could but it would not reflect a lot of what they do. The damper will take away the harsh slap that can happen...and well with it in place that won't happen.

The other ohlins for the new zx6r mount to that middle mount where most phone mounts go? Which one is this?

@NoBSZone

Жыл бұрын

This is KRT kit

Have you still got the torque settings for the center m8 bolt as i bought a used bike with this already on and want to fit a ram mount but want to make sure i torque it up afterwards properly?

@NoBSZone

Жыл бұрын

The torque is same for bolt regardless of adding the ram ball or not

@davidbarker5771

Жыл бұрын

@@NoBSZone sorry what I mean is I don’t know what the torque should be. So when I fit this ram ball i need to know what to torque it back too?

Other than the mountings any idea what the differences arecwuth the krt ohlins vs the ohlins sd042 they recommend on their site?

@NoBSZone

2 ай бұрын

No not off hand.

I’ve googled the part number and they are all 5-800$ I seen you had a comment saying you found it for close to 400 which website did you go thru?

@NoBSZone

Жыл бұрын

May have gone up in price .....like everything these days. Sportbike Track Gear is a go to for me as its local in Michigan and family owned.

Will that mount work on the 2013-2018 zx6r? I prefer that mount to the one on the center steering location that the 13-18 ive seen. Anyone know?

@NoBSZone

Жыл бұрын

Look up under the right side of your upper triple. Are there two holes?

@johnmonsalve11

Жыл бұрын

@@NoBSZoneapologies lost track of this project. Yes, the too clamp has the same and seems was unchanged. Thanks!

What levers are those? That red on them looks good

@NoBSZone

Жыл бұрын

These are Puig levers on the zx6r.

@javiermurillo4669

Жыл бұрын

@@NoBSZone thank you! They look really nice!

@NoBSZone

Жыл бұрын

@@javiermurillo4669 I am normally a ASV person but the quality, fit, finish, adjustability and overall feel of these is very nice.

By chance what is the part number for 2023 ninja zx6r krt model thnxxx

@NoBSZone

Жыл бұрын

Item # 99994-0350

Is it any difference with the 2024 zx6r install

@NoBSZone

Жыл бұрын

I doubt it.

Should be the same for 2024 ?

@NoBSZone

2 ай бұрын

I would "guess" but that bike does have some changes though i think most are cosmetic.

Is this really required on zx6r?

@NoBSZone

Жыл бұрын

If you ride aggressive or on track yes

@tcasex

3 ай бұрын

100%

Did you buy it from kawasaki ? was it a special order ? What's the price point?

@NoBSZone

Жыл бұрын

Can buy online they about $400

They stop putting them in 2004 and 2005. This was due the extra wheel balancer In the fork that was inputted and they believed it didn't need it. I rode without one for years but sad to say had a few close calls. The zx6rr had 1 but it was a add on

@NoBSZone

Жыл бұрын

Wheel balancer in fork??

@Cbrmansc77

Жыл бұрын

@@NoBSZone ya it was in the fork mounts apparently in 05. It didn't make much sence to me when I asked a tech about it one time but apparently that's what kawasaki engineered. But it did nothing when there was an emergency wheel hobble but for small vibrations it worked acceptable. But I loved my 05 636 andni had alot of good memories. But great video man I think you did a great job with the step by step instructions.

@NoBSZone

Жыл бұрын

@@Cbrmansc77 You.had someone feed you a line of BS. I been rebuilding forks for 25+ years...no such thing. Consensus is dampers were removed as a cost cutting measure as the 600 Supersport class demise and kawi less involved in support of the class. The mounting points are still present to add the damper to all models.

Just installed this exact one on my 2024. Couldn’t help but notice my instructions say to use the washer for the other bolt connecting to the bracket. So just the collars on the center and the washer for the other T40 bolt. Might want to check yours.

@NoBSZone

8 ай бұрын

Thanks I have to check it out. So far no binding and works as intended.