The fact that Honda requires you to disassemble the entire left side of the bike to put in a USB port seems insane. That said, you did an awesome job with the video. Super informative and helpful. Thanks a ton for making it!

@KSSTUDIOS

2 жыл бұрын

Thanks, much appreciated! 🙂

@lorimcquinn3966

2 жыл бұрын

It's ironic that a bike that is quite possibly the easiest liquid cooled bike to maintain, requires this amount of disassembly to install a port.

@Matt-vo1ge

2 жыл бұрын

I've gotten used to taking the fairings off but this bike is an utter pain in the arse to work on because of the myriad of screws, push-pins and multi-directional tabs. Every time something needs fitting it has to come apart.

@nomennescio4818

Ай бұрын

This is for laughing , please use the right equipment and you shouldn't have removed anything 😂😂 The portable & compact SAE to USB 2400mA charger for safely and quickly charging any USB device, including your phone, camera or GPS. Connects to battery cable with industry-standard SAE 2-pin connector - Seals perfectly when used with OptiMate SAE! ! Charges 1x USB device with up to 2400mA of current available (or get an optional O-110 USB splitter and charge 2 devices). - Charging current adapts to the connected device for safe charging. Creates a weatherproof seal against imported USB cable, or "ride-safe" cap seal when not in use - Worry-free phone, camera or GPS charging in any weather! Built-in protection disables USB charging & prevents draining your vehicle's LFP (LiFePO4) or AGM (Pb) battery - Restarts when vehicle engine starts. Monitors and displays the battery status of the parked vehicle - Indicates that the battery is 'ready to start' with a flashing LED!

I just did this mod on my 2021 NC750X DCT and can confirm that you only have to take off the black cover in front of the frunk (4 allen screws and 4 pushpins). Once that cover is removed, you can reach down with your hand and lift the harness up and off the tab that holds the harness dummy cap. Pinch the bottom of the harness dummy cap and pull the dummy cap off. Plug in the new USB attachment to the harness and lift the new harness cap over the tab that holds it to the frame and re-seat it. It took about 10 minutes.

@KSSTUDIOS

4 ай бұрын

Thanks for sharing that. I always go off manufacturer directions for install videos, but knowing the shortcuts will help some owners out.

I cannot thank you enough for putting up this film. I have just finished wiring in a front and back camera system to my bike. Without this I would never have figured out how to take the bodywork apart.

Having this video running in my garage while I was installing the usb-c port was priceless. I would never have had the courage to pull as hard as I did to get some of the fairings off without repeating that part of your video 3 or 4 times just to make sure. All back together now and working perfectly. Many, many thanks! One comment - I skipped (8) remove left side cover and (9) remove left shroud. When I finished (7) I thought I had plenty of room to install the harness and I did. I agree with the other comments that it seems crazy for Honda not to have installed this on the assembly line.

You can actually do this by just removing the black cover in front of the "frunk". Push the connector upwards from below with a screwdriver. Then you can pull the cable down and grab it under the side fairing. Doable in less than 5 min. Hope it helps someone.

@NS0O-EN33ec

Жыл бұрын

You should do a KZread on your method

@829marv

11 ай бұрын

Thanks for the tip. This was much easier then removing all the side panels.

Just found your channel. Very clear explanation. I like that you use “plain” English and don’t use expletives. Thanks for the video!

Apart from being a great video, it does show the level of design that goes into making all these parts fit together. Honda designers must be brilliant.

One of the best bike ever made!! Great Honda, and congratulations!!

Very well produced and executed video - learned a great deal about my bike - thank you

Your detailed video of the cover removal was an invaluable service to me. Thank you so much!

Wow man that was one heck of a great explanation. Thank you and keep them coming. Appreciate you sharing. Just finished installing a radiator guard and pair of ewmotec footrest

@KSSTUDIOS

2 жыл бұрын

Thanks for the comment! I hope to have more mods coming up in the near future.

Thanks for the video, really helped me a lot. I just installed 2 USB outlets, heated grips (Koso HG13) and LED brake lights for my Givi V56 topcase. I installed a simple USB cable from Amazon in the front compartment and an extra on the handle bar instead of the expensive Honda part. Your video was helpful so I knew where I could get my switched 12V. I would have bet that I would break one of the side covers, the top silver one was quite tricky - at the end I had to install it 3 times because I forgot this and that...no damage except for the right heated grip: I was too lazy to check the position as the left one went easy...I did not see that this was different to previous models and it has ring at the end which has to be filed down.

Thanks for taking the time to produce a professional video. You removed the mystery of disassembly of the plastic and installation of port.

@KSSTUDIOS

2 жыл бұрын

Glad it helped

thank you for this. I will be install the usb charger on my NC750x 2023 model this weekend. Hope everything works out. Really appreciate for putting up this video

@KSSTUDIOS

7 ай бұрын

Best of luck!

Many thanks for taking the time to produce such a fantastically filmed and precise video explanation of fitting this accessory that gives a great tutorial on the removal of the panels ( one handed!) Thank you sir.

@KSSTUDIOS

Жыл бұрын

Glad it was helpful!

Used this video to help figure out where these bolts go when putting it back together. I didn't realize how many different sized bolts this bike had until I already had them all out. So thanks! I've got the USB charger and heated grips on my NC. I love how these accessories just plug right into places already in the harness.

@KSSTUDIOS

2 жыл бұрын

Glad it helped

I just purchased an NC750X same year model and color as yours. I put a center stand and USB charger accessories from Honda. I appreciate your videos very much! The tips on the disassembly of the body parts were extremely helpful! Thank you.

@KSSTUDIOS

10 ай бұрын

Very cool!

Thanks for making the video. I referred to it quite often when I installed the charger and wiring for some SW-Motech fog lights. I did end up with an extra 5mm Allen screw. Dang it!

I did this installation today, great video. I can confirm you dont need to do steps 8 and 9 as per honda's installation instructions to fit this. So its even easier 👍

Great Video, thanks so much for taking the time to make this. Very Helpful.

Never mind the USB - this video is invaluable if you are trying to work out how to get all the plastics off without breaking anything - top job. I'm going to post a link to this on the UKNCforum if that's ok?

Super detailed guide, thank you for sharing.

Excellent Video. Thanks.. Look forward to any additional that you have planned.

Just bought a 22 NC, I am spoiled by heated grips, want additional lights on the engine bars the PO installed and finally a USB port. Considering a Thunder Box to power all my gadgets. I thank you for your video, extremely informative and appreciated!

A massive thanks for sharing this information. This was my first time working on my motorcycle. Your assistance was great. Thanks again for sharing. Philip

@KSSTUDIOS

Жыл бұрын

Glad it helped

Congratulations on your new bike! I’m part of the target audience for this model. I’m thankful for your videos as they have proven this is the bike for me. My question for you is; what other bikes did you have in mind before finally choosing this one? Thanks for the mod explanation as well! Well done.

@KSSTUDIOS

2 жыл бұрын

I did a few test rides (videos available on the channel) prior to purchasing the NC750. I tried the 2020 Harley Livewire, the 2021 Zero FXS, the 2020 Honda NC750X and the KTM 390 Adventure. I liked last year's NC750X so much that I put a deposit down on the 2021 that very same day even though it was months away from being delivered. The Honda ended up being a better all-rounder for my needs which is why I went that route.

you are a time saver!!! Thank you for the detailed step by step. Worked like a charm!

@KSSTUDIOS

Жыл бұрын

Glad it helped!

Thanks for doing this, it really helped me when installing heated grips!

@KSSTUDIOS

2 жыл бұрын

Glad it helped! I should've installed some of those while I had the bike apart 🙂

Thanks to this video I can add the charger and take the Red panels and have them wrapped a different color. Two birds, one stone! Thank you!

Love my NC. My GS 1200 side panel was 1 bolt!

Thanks for the video, just did the job myself and it helped me a lot!! 😎 just one remark, personally I think it’s just enough to remove the panels up to 6:22 min. I did the job today and didn’t need to remove more panels than up to 6:22. Thanks again and for the next DIY’ers, watch the plastic lips on the panels becuase they are weak.

Thanks for this video. Just used this info to install the OEM aftermarket USB-C charger to my ‘23 NC750XD. I believe ‘21, ‘22 and ‘23 are all literal identical models (aside from color).

@KSSTUDIOS

Жыл бұрын

Thanks for the comment 😀

Cheers from Austria! ... great video!

Thank you so much for such a good presentation and description, otherwise I gave to install a USB socket at the time of purchase, but I like the video for further repairs and modifications 👍

@KSSTUDIOS

2 жыл бұрын

Glad it helped

You make it look so easy.

Super informative! Thank you so much!

Thank you for this video, I would have been lost without it.

@KSSTUDIOS

10 ай бұрын

Glad I could help

Thanks for the excellent detailed video, I have to do this job on mine soon 👌

@KSSTUDIOS

9 ай бұрын

Glad it helped

Great video!! Thank you so much!

This bike reminds me of working on a Goldwing I used to have. Plastic panels all over and lots of bolts and push pins.

Awesome video dude thanks!

Job well done sir!

Thanks, very clear instruction👍👍

Excellent! Would have been so difficult without your video. Thank you.

@KSSTUDIOS

2 жыл бұрын

Glad it helped!

Thanks for great video and congrats to excelent one hand skill :-) Same procedure waits for me too and I have question. I saw some printed schematics on the floor. Where did you get from? From dealer or its somewhere online?

No way would I have been able to install the USB charger without your video! Very well done. Honda should be paying you a royalty. I installed mine on a 2022 NC 750X DCT. The only difference was the electrical connection at about 9:50 in the video has a clip that clips to the bike. No need for the zip tie although I used it to tidy up a bit of the wire, regardless. I'm amazed Honda doesn't just include this with the bike. The part was only about $35 but the install was ridiculous.

@KSSTUDIOS

2 жыл бұрын

Glad the video helped. I was surprised at how difficult it was to remove the layers of plastic the first time, lol

@cliftonbrown1057

Жыл бұрын

Hey Tom, I have this sub installed, but it doesn’t seem like a standard USB connector. Is there a special connector you have to use?

@tomlewis509

Жыл бұрын

@@cliftonbrown1057 I use an Android that takes a USB-C that's compatible. I'm not sure what phones/devices use Type-C.

Great video, very useful. Well done.

@KSSTUDIOS

Жыл бұрын

Many thanks!

Great job removing and re-installing the Tupperware! :))

Well done video. Thanks!

Great video, thanks very much! Beats me why Honda doesn’t install this as standard. Cost probably I guess.

Very helpful. Thank you so much!

@KSSTUDIOS

2 жыл бұрын

Glad it was helpful!

Great job and very informative. thanks

@KSSTUDIOS

5 ай бұрын

Thanks for watching!

Excelent video. Thanks a lot

Seems like a lot of stuff to take off but you show how it's done, so thanks.

@KSSTUDIOS

2 жыл бұрын

It's definitely a multi-layered fairing design on this bike. Just have to be careful on some of the delicate clips on the plastics.

Gracias por el video. Tu eres un valiente .Ya tienes un suscritor desde España. Yo estaré atento por si cuelgas mas videos de accesorios que le vayas colocando a la moto. Que disfrutes de la moto. Saludos my friend.

Very good your video, it helped a lot, from what I noticed if I connect another usb (not the original one) the male connector already exists, just put the wires in it, will it have a connector for an auxiliary headlight, thanks

The Video is great, the explanation is hard to beat. The charger, It worth the work. Is there a place to connect a portable compressor outside on the road without dismounting the entire bike? I was looking to trade my XL1200T to get a road king however my knee and back wouldn't be happy neither my pocket, so I'm looking to this lovely NC750X with saddle bags.

Thanks for the video, I bought the kit but i'm a little afraid to install my self after watch all parts I've to remove, I downloaded Installation instructions from your link,

Great video got a question if there's somewhere safe to can you open it up and see what max speed on the bike is

Thanks for this vid, great coverage! I now know I will need to pay to have someone do it...too much for me :)

Very helpful. Great explainer.

@KSSTUDIOS

2 жыл бұрын

Thanks! Glad you liked the video 🙂

Greets from Belgium! Is it really necessary to remove all panels on the LH side, or is it possible to do the job with less panels removed?

Buenas noches, felicidades por el video todo muy bien explicado paso a paso. Quería preguntar que tipo de cable se usa para cargar en esa clavija?? gracias like y suscrito

Amazing video, thanx! Fixed everything under 1 hour :) I assume its a fuse inside the fuse box (for the charger), does anyone know which one?

Very good video, thanks

@KSSTUDIOS

2 жыл бұрын

Glad you liked it!

With almost one hand?? Just amazing... Do you know what color are on this bike the 12v cables? I'm waiting in a few days my new NC and i want to install the Scorpio SRX900 alarm..

Fantastix video, kudos to you for making this video. As others have said, it seems to be an insane amount of work just to install a simple usb charging socket.... I'd rather chuck a portable power bank in the storage compartment and be done with it!

@KSSTUDIOS

4 ай бұрын

I've heard that you can do this without needing to take off the side panels, but I always follow manufacturer directions when doing an instructional video. It's still a lot of trouble for a simple USB port.

Great video! Do you know if there is a live wire on the USB harness?

@KSSTUDIOS

Жыл бұрын

Not that I know of. This module is meant to be switched so that it does not drain the battery when the bike is turned off.

nice video! helped me a lot... thx

@KSSTUDIOS

2 жыл бұрын

Glad to hear that! Thanks.

Thanks!!

The anxiety that this video gave me 😨 well done mate. But I think I will ask someone to do it for me

Thanks a lot

Thanks!

@KSSTUDIOS

Жыл бұрын

Thank you for the sub. Hope the video was helpful.

This was very helpful. Are you a teacher? The instructions were so easy to follow...and I might just use this as my guide when I do the same. Silly question but what is that tool called for when you have to "push in" some of those little plastic snap-in thingies? lol

@Viking_Kong

2 жыл бұрын

You can use a center punch or awl to push those center pins in.

Hi great video thanks, do you know if your bike had the sub harness for fog lights, or was the wiring on your bike as standard?

@KSSTUDIOS

2 жыл бұрын

I believe the wiring harness is already in place for the fog lights and they just need to be plugged in. I'm pretty sure I came across that harness while working on the USB module install.

Very good video

@KSSTUDIOS

2 жыл бұрын

Thanks

مقطع مفيد جدا ، لكن كيف أطلبها للكويت ؟ شكرا لك على الشرح المفيد 🌷

what battery tender did you use; that fits ok ?

For some reason the first top front fairing (silver) just doesn't come off. while i take it you have a very strong hand, i feel like i am going to break it if i just pull stronger on it. Any tips on those big fairing push nubs? (not the snap rivets) thanks for any clue.

@KSSTUDIOS

10 ай бұрын

Yeah, you don't want to pull too hard on the fairings as they have delicate pieces on them. If you're talking about the rubber grommets with the push nubs, they can be tight the first couple of times. It helps to pull straight out from where they are located. Hopefully, the video will give you a good idea of where they are at so that you can focus in those specific areas.

Si te funcionó con carga rápida?

good idea to charge when bike is off; phone does not take enough power to drain even if on for hours.

Do you have a vid on how to fit battery tender lead ? cheers Dave

@KSSTUDIOS

2 жыл бұрын

I don't have one specifically on that topic. If you are inquiring for the NC750X, the battery on this bike is behind a panel in the front storage area. The dealership drilled a hole in that panel so that the battery tender cables could be run through into the storage compartment.

I just brought home the exact same bike and it's great. I did notice though that the wind noise is extremely loud on my helmet. I had to pull over and put in ear plugs. I am going to have to research to see if other windscreens are available that will cut down the noise. Surprised at this oversight by Honda.

@KSSTUDIOS

2 жыл бұрын

I have a very loud helmet as it is, but this bike does seem to direct some extra wind up under my chin. Honda has a taller windscreen available that I may try out eventually.

@thomaspaschka9557

2 жыл бұрын

I have the same noise problem. Unfortunately, due to lack of 2021 bikes to the manufacturers, the have yet to update their products that are compatible to the mew version. Please post your comments if you find a quieter windshield.

@CLOUDBURST99

2 жыл бұрын

I just test-rode a 2021 with the taller windscreen on and the noise was terrible. I'm going to pick up my brand new 750X next week. Will go for a Givi or Puig windshield then.

@Truthseeker71

2 жыл бұрын

@@CLOUDBURST99 I bought one of those small clamp on wind screens that you mount to the top of the normal windscreen and is adjustable. It made a big improvement!

@KSSTUDIOS

2 жыл бұрын

@@Truthseeker71 Was that on the stock windscreen or the taller one?

As said, great video. Don't suppose you'd consider buying a 2019 750x and doing the same video..lol

👍👍👍

I'm really interested in getting a 2021 nc750x dct. I was wondering if you paid cash and if you did how did you break it out to them? Like at what stage did you let them know you were paying cash, if you did indeed pay cash. My concern is the dealership screwing me over for paying cash.

@KSSTUDIOS

2 жыл бұрын

I financed mine and paid full MSRP since they were really hard to find at the time. The dealership didn't have any reason to haggle on price because they were in such high demand. From past experience though, I never let them know how much cash I'm putting down until the out-the-door offer has been accepted. Hope that helps.

Wow I never knew there was so much in it just to get a usb connected

Nice 👍

@KSSTUDIOS

2 жыл бұрын

Thanks ✌

I've got some heated gloves. Can I attach the harness to the battery and run the harness cable out the bottom/side of bike? The cable is too thick to close the frunk on. Thanks

@KSSTUDIOS

Жыл бұрын

There is a hole in the bottom of the battery tray and you might be able to run a cable through it. If you are not using the Honda USB charger kit then you can pop out the rubber piece and run a cable through there. Hope that helps.

@christopheryack580

Жыл бұрын

@@KSSTUDIOS thanks. I'll let my mechanic have a crack. Just pput some small givi panniers on the NC. It came with a big Madstad screen and there is so much wind protection that I don't need ear plugs and can ride with my helmet visor open..it's pretty unbelievable the difference between this bike and the bonneville. Great commuter. I have the standard tranny. The engine is not like most bikes but I've figured out where the sweet spot is and I can keep it in the torque curve now and it is plenty fast for the street. The bike came with a ton of farkles...front fender extender, rear hugger, that screen, battery tender, Giv pannier and top case racks and crash bars. With 2K miles on her. I may upgrade the suspension but stock suspension is still waaay better then my Street Twins. The Tiger would have been $4k more and It just seemd the Honda would be the better year round commuter...certainly not as fun as the Tiger

Good👍

What if I just want to put an underglow on my motorcycle? Will that USB Tender kit still drain the battery completely????

@KSSTUDIOS

2 жыл бұрын

This USB charger kit shuts off power when the ignition is turned off. It shouldn't cause any drain on the battery if everything works ok.

why not tie direct to the battery; with fuse and switch; far easier ?

@bunnoatnichibei

Жыл бұрын

When I'm on all-day rides, I charge my Sena while I'm eating lunch so it doesn't run out when I'm looking for my motel. I can do this because mine is not switched.

Hi I’ve been trying to order that part every were no body know that number would u have the name of the shop Honda site won’t let me pick for my cart

@KSSTUDIOS

2 жыл бұрын

That part has been sold out for quite some time now. I ordered directly from the Honda accessories site when I got mine and had it shipped to a dealer to pick it up.

Is this product a micro usb plug to micro usb plug at both ends? the opening looks way too small to be a regular USB plug. Am I missing something?

@KSSTUDIOS

2 жыл бұрын

It is a USB-C plug, which is smaller than a traditional USB (Type-A) plug.

just add a switch on the cover.

👏👏👨‍🔧

To remove all the plastick i worse then installig the usb lol

Biceps video, but Honda should done this much easier 🙁

push clips plastic. omg getting cheap vs a bolt ! aye ! they never least in heat, humidity

Honestly, I gave up at the 6 minute mark. I cannot believe how much work just to install a usb port. Honda should be ashamed.