Excellent video, very detailed. It's great that you have specified the tightening torques for the engine and transmission drain and fill screws. Thank you very much and greetings.

Nice machine! I commuted on something similar for years, there's usually space under the seat for storage and the front fairing usually does a decent job of keeping wind/rain off your legs and feet. Peace of mind with the service too👍

Belle demo . Super 😊

Just what I needed. Thank you!

Very good video mate, thank you!

Très beau tuto. Bien réalisé . Simple à comprendre

Thanks for this video this is useful

Very helpful video sir ❤

Very good Video 😀thanx

Thank's for the video

Like your video very helpful ❤

Gear oil is also 10w30

Thank you for your video, my horn has failed to operate, I just recently found where it is located on my Vision 110. But I don't know the order of the panels to gain access to it.

merciiiiiiii👍

I overfilled my MkII Escort with engine oil in the '80s. Everywhere I went, I left a huge, white smoke screen. But, like the idiot that I was, I soldiered on.

You will find a syringe would be very helpful when refilling the gear oil and the oil is a lot cheaper buying bigger bottles.

Helped with final gear oil reccomendation

@stefanichev2684

Жыл бұрын

Using the same engine oil for final gear is wrong

@cridff

6 ай бұрын

Para la transmisión final es mejor 80w90?​@@stefanichev2684

No es mejor para la transmisión final un 80w90 ?

Thanks for the vid - where did you purchase the o ring and washer from ? Many thanks

@autoknight747

8 ай бұрын

I got them from a large Honda motorcycle dealer that has a really decent parts department.

-Que cantidad de valvulina lleva la caja de transmion ? -Que densidad de valvulina lleva? Gracias espero que me respondas a las 2 preguntas😅

Hi. Could you advise me on the washers required as I won't know the diameters until I remove the old ones. Thanks.

@autoknight747

Жыл бұрын

I bought the sump plug washer and gauze filter cover o-ring from a Honda motorcycle dealer. They had them in stock. I didn’t change the final drive bolt washers as I didn’t feel the need.

Did it take the extra final drive oil because the bike wasn't level? Or does the manual say to check the oil level whist on the centre stand?

@autoknight747

Жыл бұрын

The handbook didn’t state re. the level being check on the centre stand. I thought exactly the same and did consider getting it off the stand and allowing sone to drain out. Then I thought if more than 20ml came out I’d be worried so decided to leave it. Being a perfectionist can sometimes be curse!

What are the dimensions (inner/outer diameters and thichkness) of that aluminum washer for the engine oil plug?

@autoknight747

11 ай бұрын

This component is now fitted to the bike so I cannot measure it!

Do u have a link to the rubber seals i cant find them anywheree

@autoknight747

7 ай бұрын

I buy my components from the Honda motorcycle main dealer where they have a parts department.

@dusknade6103

7 ай бұрын

@@autoknight747 my oil is 10w -40 is that ok i have a honda vision 110 2014

Hi, thanks for the video. Does anyone know where is the oil filter located on version 2021, please?

Can I use engine oil as gear oil.

@autoknight747

Ай бұрын

Some people do but I prefer to use the correct gear gear oil.

Hello good afternoon. Thank you for the information, please, what is the specified frequency for changing the transmission oil? The oil used for transmission is a correct 10w30? (special for 120ml transmission)

@autoknight747

Жыл бұрын

The handbook for my bike indicates replacement every 2 years. My research suggested the correct oil is as detailed in the video.

@JeisonTerci

Жыл бұрын

@@autoknight747 Ok thank you for the information. Does it matter if it's 10k or 50k km? But anyway I will change it immediately and follow it at least every 10k km.

@autoknight747

Жыл бұрын

@@JeisonTerci It does not state a mileage interval, just every 2 years.

@JeisonTerci

Жыл бұрын

@@autoknight747 good to know, thank you very much! Have a nice day!

haha, I've never seen anyone use a torque wrench doing up a sump plugs ( also the gloves, LOL ).

@autoknight747

8 ай бұрын

It’s not that unusual. Using a torque wrench is better than stripping out threads on aluminium casings. Dealerships I worked for started providing gloves from the mid ‘90s and we all wore them. Before that it was barrier cream. If you work with vehicles all day you need to protect hands - mess them up and you can’t work. Used engine oils are carcinogenic, after all.