It's like ford doesn't want anyone to ever remove that headlight assembly. Very informative video👍

@phayes4031

4 жыл бұрын

You can do this from the fender well. This is how I ALWAYS do mine

@irishuwould5185

Жыл бұрын

Remove one bolt on the air box and take it out or move it out of the way and you’ll have full access from up top.

Great details on the installment of the turning light

@jasonstewart8926

5 жыл бұрын

How do get those sweet t 👕 so 🎸 that in Canada

You are right they don't the vehicle companies want to add more stuff to each and every vehicle with the "aftermarket stuff" in their factory so they can charge more.

Hey headlight revolution great job man.. I have a question. I already have installed the front led turn signals lights with the resistors on my 2018 ford f150. But I have this situation: The front turn signals lights works perfectly when the truck is working with the battery, I mean the switch is only in ignition position. But when I turn on the truck (start the engine), the front turn signal lights still works but with flickering. It's weird because the lights works properly again if I shut off (stop the engine) the truck. Could this cause by a ground issue? Could it happening 'cause I do not have attached the resistors to the metal chassis of the truck? I hope that you can help me with this situation. Thanks a lot!

Getting ready to do this to my 2019 Ford F-150 that came with Halogen Bulbs. Diode Dynamics: HP24 Switchback LEDs w/ Resistors SL1 Low Beam LEDs w/ Anti- Flicker Module SLF Fog Light LEDs HP36 Cargo LEDs HP11 Backup LEDs HP5 License Plate LEDs

@HeadlightRevolution

2 жыл бұрын

Nice! That will be a killer set up!

Also you can get to the back of the headlights just by pulling the inner fender away it’s a lot easier than removing the headlight

@HeadlightRevolution

6 жыл бұрын

Matt my man, you are right again! We did it the way we did in this video so we could really show people the details of what they're looking at!

@irishuwould5185

Жыл бұрын

I know I’m 5 years late but just remove one bolt from the air box and move it out of the way and you’ll have full access from up top.

Is that soldering gun a butane powered?

Great video! My question is if I already put load resistors on rear turn signal led lights, do I still need to put resistors on front turn signal lights? Thanks!

@HeadlightRevolution

3 жыл бұрын

Yes you do.

Is the original bulb connection ck or non ck. On the website it ask. Wasn't quite sure

I jackbup the truck, pull the tire, pull back the wheel well thing and poof , done in 10 minutes without pulling plastic (and risk breaking plastic pins and clips)

@HeadlightRevolution

Жыл бұрын

That is smart too!

You dont need the resistors. I use Forscan to turn off flasher warning.

@Stl515273

2 жыл бұрын

What module is that located in? I ordered led switchbacks and don't wanna do resistors.

I just bought a 2018. Do you sell lighting packages. If so how much for the front of the truck including bulbs and any other resistors that are needed. And a price on the bulbs for the back of the truck including everything needed. I have been watching you Chanel for months knowing I had to upgrade my lights when my truck arrived. Great Chanel!!

@davisexton8952

6 жыл бұрын

I’m looking for good bulbs not poop ones. Lol. Thx

My god I just got this truck so when the headlights burn out I am not doing this my self knowing my luck I’ll fuck up the painted trim

Will the same work for a LED switchback style light?

@HeadlightRevolution

5 жыл бұрын

Sure will!

For you owners of 2016 FX4 the factory fender flares need to be removed, no big deal, I used a set of plastic pry bars to get them off. There is a video of how to remove them but really not very clear and not the easiest way to remove them. And on this video at about 2:45 the plastic support under the headlight has some sort of vent that clips in to the support. Easy to unclip with long screw driver. Of course I snapped the little clip on the top of the headlight "fuck" looks to be just an index point. Other than that is was a sweaty afternoon in the garage on a humid July day in Virginia

@joshdapra

6 жыл бұрын

Greg Scott no you dont. Just the front clips.

Will the gtr canbus switchbacks fit in the f150 so I wouldn’t have to install the resistor

@HeadlightRevolution

5 жыл бұрын

They should fit the f150 just fine but we haven't tested them in every vehicle out there. Depending on what year F150 you have they may work better than some.

@garry4378

3 жыл бұрын

Use forscan

Although LED upgrades are nice. My concern is are they DOT approved ? Not worth the money if they aren’t...

Do they make them for my 2008 Pontiac g6 gt GTR led blubs turn signal cost ?

@HeadlightRevolution

5 жыл бұрын

Sure do! Link: headlightrevolution.com/gtr-lighting-carbide-series-3156-3157-led-bulbs-c-k-compatible/ Resistors needed: headlightrevolution.com/gtr-lighting-50-watt-6-ohm-gold-style-resistors-for-custom-installation/

@jasonstewart8926

5 жыл бұрын

@@HeadlightRevolution .how can my hands on t shirt so 🎸 in Canada

How much do you guys charge to do this to a truck ?

@HeadlightRevolution

6 жыл бұрын

Are you asking how much we charge for a full lighting upgrade or how much it costs for us to actually take your truck and we do the lighting upgrades? Because we do not take vehicles in and do the lighting upgrades, so we do apologize!

You don’t need the resistor for this truck I have led switchback leds the bulbs flash normal just the interior flashes fast, not worth cutting into the factory harness

@HeadlightRevolution

6 жыл бұрын

Matt, you're right. If you don't mind the fast blink alert on the inside of your truck, skip the resistors! Thanks for watching.

@cjs033

6 жыл бұрын

I found that mine does exactly that. Flashes normal at the rear, but hyper flashing inside the cabin. Would a Novita EP-27 flash relay fix that issue?

Don't use the resister. Get a led flasher, and you only need one, costs about $10.00.

@HeadlightRevolution

6 жыл бұрын

Wayne Sheets unfortunately on these trucks, like most modern vehicles, there is no replaceable flasher module. The blinking function is controlled by the BCM and resistors are the only option.

Dude just do it from the fender well.

@HeadlightRevolution

4 жыл бұрын

We’ve released a new video showing it done from the fender well.

All that for a bulb

@HeadlightRevolution

10 ай бұрын

Bulbs going out is normal, better to replace them for your own safety!

Unfortunately, soldering wires in a vehicle harness such as this is inappropriate. Soldering of wires should only be to printed circuit boards. Solder makes the wire fracture prone, and who knows what type of flux residue is left up in the strands of the wire. In the electronics world, low activity flux is required for wire tinning for a reason. The proper method of wire termination in this instance is with properly crimped terminals, and if you're ambitious, contact grease on the wire. The crimps should be shielded with a sealant of some sort (butyl, etc), and then covered with tape or heat shrink. The 3M heat shrinkable butt splice connectors work well too, if you know how to crimp them properly. If you have ever dissected a wire harness in any vehicle, your will only find crimped connections. This is true of Ford and Chevy, but also Boeing and Lockheed Martin........

@HeadlightRevolution

5 жыл бұрын

Good to know! Thanks for the feedback Dan! We will have to try your method.

Easier to do this by opening the fender well and not disassembling the entire headlight assembly. You can thank me later

@VicMKV

3 жыл бұрын

any video link to going in that route? I only need to change the turn bulbs

@irishuwould5185

Жыл бұрын

Remove one bolt from the air box and move it out of the way and you’ll have full access from up top. Thank me later.

I can’t believe that Ford make difficult pieces just for switch a little bulb 🤦‍♂️.

all that for nothing ppl dont read owners manuals🤣

@HeadlightRevolution

5 жыл бұрын

Very true!