2009-2012 Nissan Altima 2.5 Bad Wheel Bearing/ Replacement (Grinding noise!!)
Автокөліктер мен көлік құралдары
Welcome again to another video! In this video we will be swapping out a bad wheel bearing on this Altima! This technic can be applied to any Nissan model.! So, sit back and enjoy the video! If you're not subscribed to my channel, maybe consider subscribing and just maybe there may be a video for you!
How to replace a wheel bearing.
Nissan Altima.
Altima grinding noise.
Nissan Wheel bearing replacement.
Nissan Altima, Sentra, maxima wheel bearing replacement.
Easy wheel bearing replacement.
21mm Socket for the lug nuts.
22mm Socket for brake bracket Bolts.
14mm Socket for the caliper bolts.
32mm Socket for the Axle Nut.
17mm Socket for the wheel bearing bolts.
Email: Foreignwerks15@gmail.com
Disclaimer:
Due to factors beyond the control of Foreign Werks, I cannot guarantee against improper use or unauthorized modifications of this information. Foreign Werks assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information AT YOUR OWN RISK. Foreign Werks recommends safe practices when working on vehicles and or with tools seen or implied in this video. Due to factors beyond the control of Foreign Werks, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not Foreign Werks!
Пікірлер: 34
Gracias mi amigo! 😊
@Fwerks.1592
3 ай бұрын
Gracias a usted! No se le olvide supportar el canal!
I found easier for myself to remove 2 bolts from shock and one on the bottom and axle rod and take the whole thing out on the ground. Didn't have to disconnect steering tie rod. Its alot of more acess to 4 rear bolts and old hub was so rusty I never would be able to remove it if it was still hanging on the car. I put it facing lug bolts down on 2 pieces 2x2 put 32mm socket on rear of the bearing and hit with sledge hammer and was able to remove it from like 10 th hit. Then reverse assembly make sure before put it back on axle rod that hole for sensor matches with hole on new part and make sure dust shield facing right side otherwise wont be able to install sensor and caliper
Everyone’s saying the middle axle nut is 31 but mine is bigger
@Fwerks.1592
4 ай бұрын
It’s a 32mm socket for the axle nut.
@visionarybrushstroker7694
4 ай бұрын
@@Fwerks.1592 I meant 32, but my drivers side is bigger than a 32 for some reason.
@Fwerks.1592
4 ай бұрын
@@visionarybrushstroker7694 that’s odd! Is it a size 33? It’s probably an after market cv axle and it was probably replaced at one point.
@visionarybrushstroker7694
4 ай бұрын
@@Fwerks.1592 yea it ended up being a 36
Do you use a torque spec on the 32 mm nut on the axle? Or just tighten to your liking? You can also take the two bolts holding the caliper on and take the whole brake assembly off as on piece. Use a zip tie or such to hold it.
@Fwerks.1592
Жыл бұрын
I get it lol, trust me I have all the special tools required. A lot of people don’t have a torque wrench, I didn’t want to discourage anyone from doing work on their car. The axle nut was torque to 130lb of torque off camera. Also for the caliper I always make sure they never hang off the brake line, last thing you want is a damaged brake line. It’s not my first rodeo , I do thank you for watching and any feedback!
@gregsmith332
6 ай бұрын
@@Fwerks.1592 How do you know that the axle nut was torque to 130 ft-lbs? You used a breaker bar, not a torque wrench.
@Fwerks.1592
6 ай бұрын
@@gregsmith332 oh here we go again Greg with the whole torque spec.
@gregsmith332
6 ай бұрын
He just tighten it to his liking because he used to breaker bar.
@Fwerks.1592
6 ай бұрын
@@gregsmith332 Greg are you here for the torque specs or are you here to get an Idea how to replace a bearing? That's the reason you are watching this video!
Hey Novice Mechanic here......Could we just remove the Caliper and Bracket all as one unit instead of taking two pieces off at different times?
@Fwerks.1592
Жыл бұрын
You can definitely do that. I don’t know what I was thinking! I remember now! I also did a pad replacement off camera! The caliper can come off as one unit.
@Letstalkaboutsex1911
Жыл бұрын
@@Fwerks.1592 ohhhhhh ok! Hey thanks for the response!! I didn't want to fubar something trying to be different lol appreciate you sir
Who is manufacturer of that wheel bearing? I was using moog and the hole for ABS sensor is not aligned properly.
@Fwerks.1592
10 ай бұрын
I used a carquest brand “ wheel bearing “ hub assembly. This one bolted up perfectly fine. Must be a mold issue on that moog.
@johnysilver1853
5 ай бұрын
You have to spin it around
@kuzmanovskinikolce
5 ай бұрын
@@johnysilver1853 No, probably was defective, I bought Mevotec and I installed with no problems. Obviously Moog quality is going down to the toilet.
Do the new bearings come prepacked?
@Fwerks.1592
4 ай бұрын
Yes they do come pre-packed with grease!
@jameskells1844
4 ай бұрын
@@Fwerks.1592 many thanks
Is it also the reason you would hear a humming sound??
@Fwerks.1592
Жыл бұрын
A humming or roaring noise can also indicate a wheel bearing issue.
@lifeofsebastian5035
10 ай бұрын
Having the same problem with my car
So if someone forgot to undo the sensor and few days later the abs slip vdc lights came on how would one test if its broken or just needs to be reset i watched the person changing mine on the rear bearings everything looks similar except no axel on rear ones and i don't remember them removing the sensor?
@Fwerks.1592
6 ай бұрын
Good question! Yes there are a few ways to check if you have access to a scanner. The abs sensor can get damaged if it’s not removed. Sometimes when they don’t remove it before installing the new bearing. The sensor collects metal shavings at the tip. Which this can cause the signal to be blocked. Go ahead reset the abs code or clean the sensor off. If you have access to see live data, go under the abs module and select all abs sensors ( FL, FR, RL,RR) it should the. Display the mph on each wheel. You’ll know if that specific sensor is bad if there is no data on display.
@musicfan07058
6 ай бұрын
@Fwerks.1592 thank you
That wheel bearing is definitely old and rusty
@Fwerks.1592
10 ай бұрын
It needed to be replaced long time ago!!
@lifeofsebastian5035
10 ай бұрын
@@Fwerks.1592 o ok
@Fwerks.1592
10 ай бұрын
@@lifeofsebastian5035 the job is pretty straight forward. Not too bad to replace.