Great video. Only suggestion would be showing the drive belt from the right side of the machine too

Thanks for showin this....These are Old but Keep Goin !!!....

@albertoguerrero5362

2 жыл бұрын

Hello Lensmanic Feleven. Thank you for your comment, and I will do my best to keep going. Thanks for watching!

Well done!

A big problem in replacing the secondary belt is stretching the idler Pulley spring. I used a combination of stretching the spring and rolling the belt over the LH Pulley. I took a crowbar ànd placed it by the pivot arm with a wire wrapped around the crowbar and through hole where the spring goes through the pivot arm. I was able the pull the pivot arm open and roll the belt on.

awesome video I've been looking for this for a long time.Thanks

@albertoguerrero5362

8 ай бұрын

Im glad it helped you. Thanks for the awesome video comment.

great video!

@albertoguerrero5362

3 жыл бұрын

Hello blind bob, I'm glad you enjoyed the video. Thank you for watching!

@proudconservative1

2 жыл бұрын

@@albertoguerrero5362 I don't know if the mower is yours but I have a 2004 just like this one. I want to change the transmission fluid and I understand it takes 20W50 motor oil. I think the bottom of the trans has to be removed to drain the oil but I don't know how far to fill it. Some trans have a bolt on the side and fluid leaks out once it's full, then replace the bolt. Do you know anything about this procedure? I just finished replacing all three belts and your video helped lots. Thanks in advance.

@albertoguerrero5362

2 жыл бұрын

@@proudconservative1 Hello, thank you for your question and comment. To answer your question, the mower is not mine and unfortunately I am not familiar with that particular process with this mower. My apologies for not being able to help you with this or lead you in the right direction. I'm glad my video help you with the Belts replacement and thank you for watching.

I like the music.

@albertoguerrero5362

Жыл бұрын

Hello Tom Dennee , yes the music is pretty cool. Thank you for watching.

Can anyone answer- The bolt loosened below the 2-pulley bracket to allow him to remove the drive belt. Should that bolt/nut actually not be 100% tight, to allow the 2-pulley bracket to float and sel-adjust for temperature, belt wear, load, etc. allowing the tension spring and engagement controls to function?

I wasn't really looking for a welding video. Seeing the remount would have been nice though.

@albertoguerrero5362

4 ай бұрын

Hello @murraymacneill2545, thank you for the comment and well noted. Thank you for watching.

Alberto great video but next time NO music we want hear you talk and get tips. Thanks

@albertoguerrero5362

2 жыл бұрын

Hello MB, thank you for your nice comment. I will definitely give your suggestion some thought. Thank you for watching.

Wish you had the video of you pulling off the seat and fenders

@albertoguerrero5362

8 ай бұрын

Yea that would of been good I agree, Its unfortunate I didn't film that part. Thank you watching.

Hi , can you change the drive belt without removing the seat and fenders? Also do the front suspension plates have to be removed to pull the deck?

@albertoguerrero5362

3 жыл бұрын

Hello Todd Shaw, thank you for the comment. You can change the drive belt without removing the seat and fenders. Also, the suspension plates do not have to be removed. Thank you for watching!

@ronduff4325

2 жыл бұрын

That was my question too. Thank you !

@ronduff4325

2 жыл бұрын

Although it looks a lot easier that way .

@albertoguerrero5362

2 жыл бұрын

Hello @@ronduff4325 . Thank you for the comment. Yes it was easier actually. But I was doing other work on this lawn tractor which was the reason for removing the extra items. Thank you for watching!

hi thanks for video. In terms of the belt #s - is this deck the 48" or 54" version ?

@albertoguerrero5362

2 жыл бұрын

Hello Instructional Desiner, it is the 48" deck version. Thank you for watching!

What size are the mower belts , in this video ?

Hi hope your doing good I just replaced the primary and secondary deck belts double and triple checks the routes look good but every time I go to engage the blade the mower dies never had that issue before please I could use some help

@albertoguerrero5362

10 ай бұрын

Hello, I am not really sure.

Great video,but why doesn’t anyone give the actual size of each belt?!!!!

@albertoguerrero5362

14 күн бұрын

Hello ToneyMann, Thank you for your comment. The Size for each of the belts are shown at the following times: 3:21 / 11:13 / 12:37. I hope this is what you are referring to in your comment and I hope this helps you out. Thank you watching.

where is part 1?

@albertoguerrero5362

2 жыл бұрын

Hello Jon Resler, here is the link: kzread.info/dash/bejne/fauglMiDlsyoo7Q.html Please let me know if you can view it. Thank you for watching!

I find it hard to see myself wearing gloves in such a cramped workspace and I find it very hard to see what you're doing in the same

@albertoguerrero5362

3 жыл бұрын

Hello The spirit Of 76, thank you for the comment. Thank you for watching.

@markbelden6919

3 жыл бұрын

Super helpful tip about the 3/8" rod and chain,

@albertoguerrero5362

3 жыл бұрын

Hello @@markbelden6919 , thank you for the comment. It does make it easy. Thank you for watching.