2003 Kia Rio clutch replacement - how to part 1 of 2
2003 Kia Rio clutch replacement - how to part 1 of 2
Жүктеу.....
Пікірлер: 17
@jean-pauldupuis809911 жыл бұрын
Did almost exactly the way you showed, and it worked out great. Thanks
@jeffsx5105 жыл бұрын
Thanks for doing the video, some great time saving tips in the vid and the comments. That superglue tip comment is a beauty
@antegas12 жыл бұрын
Thank you very much! God job
@davem533310 жыл бұрын
As others have said, not dropping the trans is not really a labor saver as you are working at odd angles and dangles. Really quicker just to drop trans. plus you can clean the inside front of the trans. A trick is to get 2 or 4 bolts like like the ones that hold the trans in place, but about 6" long. Cut the bolt heads off and screw them into the block thru the trans mounting holes so you can use them as guide pins. Remove all the other trans bolts and slide the trans back along the bolt/guide pins. Same on re-install. Makes it MOOCHO easier.
@JamesHill-cj4fn6 жыл бұрын
Another way to keep the clutch plate aligned is to center the plate on the pressure plate[right way round ] mark with pen then put a few drops of super glue between them and pop the plate on in the right position.The clutch will free on first try. Bob UK>
@slyrader112 жыл бұрын
well ive never worked on one either but im going to find out how when i do one tomorrow
@chughes37611 жыл бұрын
No this is not Dave's other account. This is a fan's account
@poopmeat1511 жыл бұрын
This is Dave's other account.
@fordErich12 жыл бұрын
U guys shut up this is an old vid that Dave reposted on his new channel this guy was just making it so people could watch Dave's vids when his account was terminated
@danielwoolley893010 жыл бұрын
That cars left hand drive mine was right hand drive (or the other way around ) really struggeled to get the gear box over far enuff would of been alot less pain to just remove it straight up
@JuanGarcia-vx2ds5 жыл бұрын
Chuck Norris?
@user-rv7lm9io1p2 жыл бұрын
Чё на русский не льзя было перевести😒
@ahmetfidan626910 жыл бұрын
if i were u i take out whole engine its too hard to work in narrow areas
@mrfabre129 жыл бұрын
good luck trying to get warranty on the new parts, first question you will get asked if whether the flywheel has been machined, if not, warranty void! Also, did I see the the car resting on a tyre with a brick on it? Great way to show what NOT to do, you must use stands. This is a very irresponsible video, someone is going to hurt themselves after watching this video and trying the same things!
@danielwoolley893010 жыл бұрын
if u have to do this on this car, in a backyard dont bother get a new car its not worth it. Just wreck car and get whateva u can 4 it.
@biker9dk
9 жыл бұрын
What? It costs like 150 bucks for this car for a clutch replacement kit why would you spend a couple extra grand???
Пікірлер: 17
Did almost exactly the way you showed, and it worked out great. Thanks
Thanks for doing the video, some great time saving tips in the vid and the comments. That superglue tip comment is a beauty
Thank you very much! God job
As others have said, not dropping the trans is not really a labor saver as you are working at odd angles and dangles. Really quicker just to drop trans. plus you can clean the inside front of the trans. A trick is to get 2 or 4 bolts like like the ones that hold the trans in place, but about 6" long. Cut the bolt heads off and screw them into the block thru the trans mounting holes so you can use them as guide pins. Remove all the other trans bolts and slide the trans back along the bolt/guide pins. Same on re-install. Makes it MOOCHO easier.
Another way to keep the clutch plate aligned is to center the plate on the pressure plate[right way round ] mark with pen then put a few drops of super glue between them and pop the plate on in the right position.The clutch will free on first try. Bob UK>
well ive never worked on one either but im going to find out how when i do one tomorrow
No this is not Dave's other account. This is a fan's account
This is Dave's other account.
U guys shut up this is an old vid that Dave reposted on his new channel this guy was just making it so people could watch Dave's vids when his account was terminated
That cars left hand drive mine was right hand drive (or the other way around ) really struggeled to get the gear box over far enuff would of been alot less pain to just remove it straight up
Chuck Norris?
Чё на русский не льзя было перевести😒
if i were u i take out whole engine its too hard to work in narrow areas
good luck trying to get warranty on the new parts, first question you will get asked if whether the flywheel has been machined, if not, warranty void! Also, did I see the the car resting on a tyre with a brick on it? Great way to show what NOT to do, you must use stands. This is a very irresponsible video, someone is going to hurt themselves after watching this video and trying the same things!
if u have to do this on this car, in a backyard dont bother get a new car its not worth it. Just wreck car and get whateva u can 4 it.
@biker9dk
9 жыл бұрын
What? It costs like 150 bucks for this car for a clutch replacement kit why would you spend a couple extra grand???
@alexandraturney7968
6 жыл бұрын
What world do you live in??