2002-2006 Toyota RAV4 (2nd Generation) Taillight Lens Assembly Removal or Bulb Replacement
This particular repair was done on the passenger side. . 0:00 Rear Bulb Replacement 1:26 Assembly R&R . . . Follow me on IG @ the.real.dadaking
Жүктеу.....
Пікірлер: 14
@stewarthoi2 ай бұрын
Thanks, I just did mine. It is not really necessary to remove the bottom trim 1:26 to 1:50.
@Wendy-jq8il4 жыл бұрын
Great job! 👏👏 You made it look so easy.
@aetakoz10 ай бұрын
4:06 there are two hoses. What’s the small one for ? Because I think I have a leakage.
@dadaking
10 ай бұрын
Pretty sure that's a windshield washer fluid line.
@mr.automation5433 жыл бұрын
Look great thanks for the vid king. Im looking to open my housing. Any idea house strong the adhesive is? Think a heat gun and pry tool will work?
@dadaking
3 жыл бұрын
Thank you. I have no clue as to what is involved in opening the housing. As you can see in this video, I didn't attempt to do that.
@andrer.27872 жыл бұрын
How long was the deep socket you used?
@dadaking
2 жыл бұрын
Just a typical 2" socket
@luckyluckyloulou6100 Жыл бұрын
THANKX
@dadaking
Жыл бұрын
🤙🏽
@XoxJasonReynoldsxoX Жыл бұрын
Make sure you have a STUPID long deep well. 2" DEEP WELL ISN'T LONG ENOUGH TO REACH THE BOLT ON THE TOP. You can get the socket on with the stupid long shank, but it'll prevent you from sticking the ratchet on. Thanks a lot toyota!
@JoeGoldberg577_
Жыл бұрын
How long and where should I get it ? I experienced this today
@XoxJasonReynoldsxoX
Жыл бұрын
@@JoeGoldberg577_ I never got mine out. I ONLY have a 2" and my drivers side would need at least 2.5" to get the socket on the nut AND the ratchet on the socket. Mine is a 2005. I ended up fishing out an led bulb that fell off INSIDE the housing after a couple hours of cutting my fingers up. It's pretty ridiculous!
Пікірлер: 14
Thanks, I just did mine. It is not really necessary to remove the bottom trim 1:26 to 1:50.
Great job! 👏👏 You made it look so easy.
4:06 there are two hoses. What’s the small one for ? Because I think I have a leakage.
@dadaking
10 ай бұрын
Pretty sure that's a windshield washer fluid line.
Look great thanks for the vid king. Im looking to open my housing. Any idea house strong the adhesive is? Think a heat gun and pry tool will work?
@dadaking
3 жыл бұрын
Thank you. I have no clue as to what is involved in opening the housing. As you can see in this video, I didn't attempt to do that.
How long was the deep socket you used?
@dadaking
2 жыл бұрын
Just a typical 2" socket
THANKX
@dadaking
Жыл бұрын
🤙🏽
Make sure you have a STUPID long deep well. 2" DEEP WELL ISN'T LONG ENOUGH TO REACH THE BOLT ON THE TOP. You can get the socket on with the stupid long shank, but it'll prevent you from sticking the ratchet on. Thanks a lot toyota!
@JoeGoldberg577_
Жыл бұрын
How long and where should I get it ? I experienced this today
@XoxJasonReynoldsxoX
Жыл бұрын
@@JoeGoldberg577_ I never got mine out. I ONLY have a 2" and my drivers side would need at least 2.5" to get the socket on the nut AND the ratchet on the socket. Mine is a 2005. I ended up fishing out an led bulb that fell off INSIDE the housing after a couple hours of cutting my fingers up. It's pretty ridiculous!
Camera is jumping all over the place