Just did my sons 02' CRV EX and saw these on speakers pods and was like WTF. Did same as you did but ran tip ties through. Works great and holds tight.

Thanks so much for this video. There are a lot of fast paced, non-linear KZread tutorials for this kind of stuff, but yours was straightforward, and you explained everything and answered all my questions along the way. I can't wait to get these new speakers going!!!

You’re a legend. Thank you for taking the time to put this together.

Very good intuitive idea! Also maybe an idea to eliminate a lot of noise by road and make the sound better for the speakers would be to buy some sound and heat special closed cell foam for audio to install the door between the panel and the door as I did. My car is so quiet and my music is so clear without loss of frequency. I did all my doors. Super ultra quiet.

@olakunleolafisoye8433

Жыл бұрын

Pls what did you buy exactly? The road noise is a lot

@hankrodriguezhill7029

Жыл бұрын

I'm following, but I do know there's lots of products out there

Thanks so much for this video. Just put a pair of boss speakers into my 06 CR-V using your method. Although I had some 1.25" screws so I didn't have to cut them

Very informative and you broke it down masterfully! Thank you!

I love this car, my speakers just blown, they were oem so this is the first speaker job I’ll be doing..so excited!thanks for the videp

@eddoblede4037

9 ай бұрын

Porque te explotaron los originales 🤨

Wonderful video came just at the right time 👏🏼👏🏼👏🏼

Very helpful. I have 2 CRV's . I will be doing this to one soon.

amo estos trabajos!!!!recuperar, reciclar, refaccionar, el futuro ya llego!!!!gracias por tu tiempo!!!

Helpful hint: if you don’t want to do the wiring or buy the aftermarket adapter you can rip out the adapter from the old speaker and solder on the new speaker wire onto the adapter from the old speaker

@montisino

Жыл бұрын

Good idea 💡

Thanks for the vid, i broke the bottom clips on the my fronts prying from the bottom. Now i wont make that mistake on the rears. I did end up ordering a pair of 6.5 adapters from Crutchfield. They lined up about as well as the stock hollowed out housing does with my JBL GTO 2 ways. I wasn't able to get any screws to line up with the adapters so i ended up drilling holes on the sides of the adapter and using zip ties at every screw hole on the speaker. Not an air tight seal my any means but short of using epoxy it seems to be the best solution. They are secure at any rate. It seems using the stock housings may just be the best option.

Very helpful. I don’t own a dremel so I instead I bashed all the plastic brackets off with a hammer and flathead screw driver. I drilled holes in the plastic mount and used zip ties instead as I didn’t have the right screws (worked great) and final to mount in the door I screwed a hole in the door just above the existing hole that holds the top metal clip and zip tied the speaker in place. If you had trouble keeping the plastics together and limited tools I hope that can help Ps I broke off the connecter from the original speaker and used that to connect the new cables instead of buying an adaptor

@diywarren1776

2 жыл бұрын

Is it just two wires coming into the connector?

Thank you. I will do exactly what you did. Sounds fun.

Maybe an idea for other DIYers, instead of using screws to mount the speakers to the original bracket, you could drill/punch the same three holes and use smaller zip ties to fasten them. I'll be getting an 03 crv soon and will want to do the speakers. Other than that, this was an excellent video. I'll be going your route and reusing the original mounts as I haven't found any replacement mounts anywhere else. Beautiful! Very well done.

@m0niker

Жыл бұрын

I like this idea. I'm going to try this soon and that's the only part I'm apprehensive about

Great idea! Thanks man!

'Hope it helped' ............... I should say so. Thanks. Terrific. I would have used flat head machine screws with nuts myself but this was a great instructional video.

Very helpful. Thank you bud!👍

Thanks! Just made my day…

what a great video, bravo. even the same year as mine. thanks G

Awesome!! Thanks for the video

Nice job thank for sharing.👍

As per other viewers, capital job and really very useful. Thank you. A few questions if you are still here! 1. Do you recall the maximum distance from the face of the speaker that a tweeter could protrude before interfering with the door speaker grill, i.e. how much clearance is there? 2. How deep can the speakers be before they interfere with anything inside the door, e.g. window perhaps? 3. Dis you do a front door speaker vid or is the setup exactly to same with the same clearances?

Dude's hand is cut and bleeding. Just like mine will be when I get done.

Hint: Remove the door panel by pulling up from the bottom. I started the process from the top right and the plastic cracked. It was old brittle plastic, of course.

@scottr1892

3 жыл бұрын

There is a tool that is like a big pair of pliars made specifically for removing panels and clips as not to break the clips or cause any damage. I take my panels off in about 30 secs after removal of retaing screws. The tool is not the single screwdriver type. That is a lot more difficult and can scratch or not fit right and cause other damage to the door panel and door. It is only about $6.00 US with shipping and heavy duty, high quality. This the link. Just look for the best price and get a package deal with other plastic removal tools together. It will cover all you need to do the job easily and professionally at a very low cost for many jobs. shopee.ph/EDB*-Car-Door-Card-Panel-Trim-Upholstery-Remover-Clip-Removal-Pliers-Pry-Tool-Set-i.345394535.9309366624 Look on Ebay or wherever you order online. 39 secs is all it took me to remove my panels off no damage.

Can we eliminate the factory connector and splice the wires directly into the car's wiring?

Those screws are so orky I love it :D

Thanks dude

Awesome job thanks

Nice video

5 star video

True mechanic hands here :D

thank you so much for the video, I'm going to do the same, its the same process to the four doors? and i have to buy two pairs of the same speakers? thank you!

@lukascruzat51

3 жыл бұрын

i just see the answer, its the same to the four doors, thank you for the video!!

I just bought a new crv ex model coming from the accord coupe that had a sub. Needless to say I love the car, but the stock stereo leaves me wanting more. What brand are the stock speakers in these? They have no bass

@brentfarnsley2028

4 жыл бұрын

They are not labeled so I'm not sure who the manufacturer is

Can u add links to all items used

what kind of head unit do u have? where did u get it from?

Hi there. I'm about to replace my speakers on, ironically the exact same year and color CR-V! I'm curious if you are happy with the speakers you put in and if they work better than the factory ones? Many thanks for putting out this video! Thumbs up!

@brentfarnsley2028

4 жыл бұрын

Yes I am very happy and they sound way better than the factory speakers. They are on the low end of the quality spectrum but they are 10 times better than the paper cone, plastic basket, non existent magnet OEM speakers. I would definitely do it again!

@coryavila01

4 жыл бұрын

@@brentfarnsley2028 - Perfect. As long as they're better, I'm there. Thank you so much for responding so quickly!

Great video. Does the front door utilize the same wiring harness interface? I'm sure it does but want to be sure. I'm in need of new speakers really bad.

@brentfarnsley2028

4 жыл бұрын

Yes it does. All four doors are the same.

@leolionz3692

4 жыл бұрын

@@brentfarnsley2028 thank you! I can't believe how much some company's are charging for OEM speakers with the adapter. Good thing I can do it this way. Thanks again for the feedback.

Nice setup bro ? Did you replace the head unit Stereo as well

@brentfarnsley2028

5 жыл бұрын

It is an aftermarket Sony head unit. It was in the car when i purchased it.

@thexflexclan

5 жыл бұрын

Brent Farnsley ok nice I just bought a 05 Crv se model and I kinda wanna get an upgrade of those speakers 🔊 I guess would be nice to get an aftermarket unit as well

you have a link, but i see it says pair, that means two, so did you buy to sets? I want to try this myself with my daughter and want to follow your steps, thank youyou.

@brentfarnsley2028

3 жыл бұрын

I had to update the link because the package of four speakers bo longer exists. So yes, you will have to purchase two sets of speakers.

Do the windows have an problem hitting the magnets?

thanks for your time in showing how to get to the speakers, can anyone suggest a good headunit that fits well in a cr-v 2005 replacing stock model,cheers

@ScienceLarson

4 жыл бұрын

Installed this one over the winter, the wife is thrilled with it. smile.amazon.com/gp/product/B07CB3CB1V/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1

if I putting this much time on this work (which I did on my MDX), I would put the best speaker I could afford. "Buy once,Cry once"

@factotumted

Жыл бұрын

I'm just getting around to doing this on my 2004 crv, I bought some nice six and a half inch jbls for 80 bucks a pair x 2. I also put in an atoto Android 10 inch head unit

My mount for my 03 crv wasn’t big enough for the speaker. It sticks out about a half a centimeter. Will that affect my door panel?

@brentfarnsley2028

3 жыл бұрын

It should be fine. If you need to widen the mount a little you can use heavy grit sand paper or a grinding disk on your rotary tool. Good luck.

What is the actual size of the speakers inside a 2003 Honda crv

@tylerkriesel8590

Жыл бұрын

6.5 inches

I have to ask. Did anyone else run into problems with the driver door speaker? I thought I had it right because I did the other 3 no problem but the last one was the hardest for me

Thanks for sharing 👍👍👍 (you cut your hand...)

why doesn't the sound in the rear doors of my crv work?

what was the speaker interface you used?

@brentfarnsley2028

4 жыл бұрын

I put this in a previous reply but here it is again. www.amazon.com/DKMUS-Harness-Speakers-Adapter-Connector/dp/B01G1TA90E/ref=mp_s_a_1_1?keywords=DKMUS+2+X+Pairs+Wire+Cable+Wiring+Harness+for+Honda+Acura+Speakers+Adapter+Connector+Adaptor+Plug&qid=1578972914&sr=8-1

what model speakers did you get?

@brentfarnsley2028

4 жыл бұрын

Boss model # CH6520

hello there. do you have a link to these interface cables?

@brentfarnsley2028

4 жыл бұрын

www.amazon.com/DKMUS-Harness-Speakers-Adapter-Connector/dp/B01G1TA90E/ref=mp_s_a_1_1?keywords=DKMUS+2+X+Pairs+Wire+Cable+Wiring+Harness+for+Honda+Acura+Speakers+Adapter+Connector+Adaptor+Plug&qid=1578972914&sr=8-1

@brentfarnsley2028

4 жыл бұрын

There are others but these will work.

How many hertz does the cr v produce

@brentfarnsley2028

4 жыл бұрын

I think you might be referring to decibels (db) but I have an aftermarket head unit that only puts out about 16 Watts of power so it is not very loud. It is adequate for the average listener though.

It is a great video thanks! I agree the OEM speakers are piece of crap and needs to be replaced, however nobody talks about the tweezers on the top of the dashboard. Most speakers have their own crossover and you should use those instead of the OEM (I do not even know if CRVs have crossovers somewhere in the body, but since there are tweezers on top, the signal should be filtered somewhere??), that means you need to rewire everything otherwise you might end up connecting your speaker to a non compatible crossover on the way and the sound will not be as good. I would rather use the factory wiring since then I do not have to dissect the entire cable system, but have no idea how to map and find the OEM crossover to eliminate it.... Anyone has an idea?

@Titans2138

2 жыл бұрын

Some models don't have tweeters. If you do have a tweeter I suggest replacing it along with the wiring and you won't have to worry about a factory crossover but the crossover is probably just a capacitor attached to the tweeter. I don't know, that's my guess.

@fuzesizoltan1518

2 жыл бұрын

​@@Titans2138 Thanks but I figured it out in the meantime, but you are absolutely right. The 2006 Honda CRV speakers have only a capacitor, right next to each tweezer's plug, that is it. I placed the new crossovers under the middle console and used my own wiring to both sides from it to the tweezers. For the large speakers I could use the factory original wires that went from the hifi thorough the doors. It is as simple as that, no rewiring is necessary for the door speakers. The only problem is that I have to replace the OEM speakers in the rear doors as well, because now I can clearly hear how horrible they are!! :))

Dang. $45 for the replacement adapters on Amazon. Wow.

🤓

I thought these were 5 1/4”

It would have been really helpful if you showed how to put it back as well. The process is not really exactly the reverse

@brentfarnsley2028

5 жыл бұрын

Sorry, i didn't really have time or ability to do it at the time. Reversing is pretty easy, you just make sure you have the door panel fasteners in place around the inside of the door panel. Next reattach the wiring harness to the window switch. Next, slide the door panel window weatherstrip side in first as you line up the door lock plastic rod through the notched hole at the top of the panel. Once the weatherstrip side is slid into place and door lock rod in position, look around the edge of the door panel to ensure the plastic fasteners are lined up with the wholes and then pound them back in with your hands and fists with some light pressure. Then reattach the triangular panel putting the clip in first and then pushing in the center pin fastener. Then reattach the door latch metal rod and clip. Reattach the two screws for the latch and two screws for the main door handle snd that should do it. Sorry again for the lack of detail.

@ryanmccue8180

2 жыл бұрын

@@brentfarnsley2028 you're a stand-up guy for this reply God bless you sir

i remember this one crv i got to drive bak in ~04-05ish not really too sure... anyways that fuckr had a fuking crazyass system! idk if the speakers were aftr market or stock becuz the stereo unit was stock but shit seemed lik there was subs hidden in tht bitch.

the door panels dont fit

@keedot-ro9ey

5 ай бұрын

they fit in the front but not the back

cut off harness and tape wires up

These are the most ridiculously fiddly speakers to replace 🤦‍♂️. My ‘98 Forester took two minutes per speaker as the speaker grille comes off the door, allowing full access!

Bad idea.. Hours of labor and its gonna start rattling after time.. big thumbs down

@StevXtreme

9 ай бұрын

Why on earth would it start rattling?