Parts linked in the description!

Watched this video and your video on installing the amp/sub, couldn't have successfully done everything myself without you! Thanks man! Cheers

I dropped a green zanax in my console so now I am here

@ozboz6452

4 жыл бұрын

Layne Duran Your mom will find it dont worry

@realonereal1

4 жыл бұрын

@@ozboz6452 this joke could be taken in so many different ways

@jacobwithee3848

2 жыл бұрын

Incredible hulk

@cfrmdaraq5894

3 ай бұрын

Dumbass

Thanks for the video. I was able to install the same stereo into a 2002 civic lx using most of what you posted here. To others trying this, a commenter below gave a good piece of advice on installing the mic- route the cable through the glove box instead of through the driver side. Much easier to access and you don't run the risk of tangling with pedals.

@ProvoBeastAudio

8 жыл бұрын

+CraigMammalton Thanks. The mic wire was run completely under the carpet, not around the pedals.

this is exactly what i was looking for! thanks a ton!. so well explained and simple. you're the best!!

Thanks man this helped so much, I went to my local sound store and picked up the same harness and bracket as you and it was easy as plug and play!

Was just trying to figure out how to get the paneling off so i can check and see if my cigarette lighter was connected and this helped i fixed it thanks a lot

This is the first video ive watch out of a dozen. Where you said anything about the antenna needing power.

@ProvoBeastAudio

7 жыл бұрын

The power antenna wire in the wiring harness adapter (blue) may or may not need power. It is easiest just to tie that into either the red ignition wire or the blue white wire on the radio. All depends on your year civic.

Just a note. I've seen a 2002 civic video where it is possible to remove the power socket section without removing the shift knob trim in order to access the anchor 8mm bolts. THIS IS NOT possible on the 2003. THIS video is the easiest way to get the job done on the 03. Thank you Provo beast

@Sangoreborn

8 жыл бұрын

My 2005 was like that!

@noonespecial9233

6 жыл бұрын

Thank you so much. I've got a 2003, and the videos on here have been super intimidating OR suspiciously easy.

@liveandletlive2894

5 жыл бұрын

Nope my '03 comes right out no need to remove the shift knob trim piece

very useful content and very good video, you give attention to every detail and you did like a professional. thanks a lot and keep going

Exactly the video I needed. THANK YOU!!

great video! I would have broken the dash for sure if I didn't know about the 2 8mm security bolts above the cup holder

hi i have a question, I bought a double din aftermarket stereo and I don't think it will fit my aftermarket double din dash kit so what do i do please help.

Thanks for the video. Just installed the same exact one. Installation was a breeze.

Thanks for the video. Saved me from guessing how the panels come off.

I have an 03. I left my lights on, battery died, and jumped the car...but now the radio (after factory-replaced by previous owner) doesn't work. It worked just fine before the battery died. I checked the fuses and they are fine. Any idea what went wrong and how to fix it? -update...i disconnected the battery and reconnected it and the radio works again! Simple reset did the trick :)

Great video, simple and straight to the point. New sub!

My grounding wire came loose inside the driver side (2001 Honda Civic) area and I wonder where it is supposed to anchor. Thanks in advance

Thanks, What’s the easiest and cheapest way to be able to play my music directly from my USB key in a 2004 Civic car radio? Do they sell dacs? Some recommend to install a used radio that has a built in USB input.

On my 01 Honda Civic I don’t have the blue male connector harness. When I took the stock stereo out, everything was hooked from just wires and I bought a new stereo but the colors don’t match. What should I do where can I buy a male plug for2001 Honda Civic lx?

About to install a stereo for the first time. Thanks for posting a very informative video.

Great walk-through. Thanks much :)

Thanks for the video. I only broke one clip because someone before me glued it back together

very informative video, well done mate!

thank you so much for this video! I save at least 100$ by installing it myself!

Imma bout to get 2002 civic lx coupe by monday its manual, just some advice what to know when buying it? it has 95k on mile age and 195k on chasis. should I use obd 2 to check it?

Hi can you tell me why after I put a JVC new stereo it won’t turn on thank you in advance..

Is necessary to connect the blue antenna wire to the red wire? My pioneer radio doesn't come with the blue wire.

can i use the original dash kit? i like honda’s factory CD compartment

I'm not sure what year your car is but I have a 2001 honda civic dx manual.. And for my year you just have to pop out the cigarette lighter panel and that gives you access to the 2 8mm phillips screw bolts. Then pop the 9 clips around the factory bezel.

Thank you for the video. It helped me out big time for my new radio.

Would the pioneer harnest work on an jvc headunit

Hi I brought the civic 2001 1.6 my parter changed the radio and all work fine but I got the problem with starting the engine it won't start first time and the green key light it's not on the board and this all happend after changing the radio do you know what might happend or what to do woth it aswell when I use to leave mi lights on and took the key out the car will Make A noise to turn them off it doesn't do that now please if you could give me advice what to do

love how your doing it at night with a light haha!

can you use any bluetooth radio to do it?

Thanks for amazing tutorial, worked perfectly.

@ProvoBeastAudio

8 жыл бұрын

Be sure to subscribe! Thanks for watching!

Great video, helped me a lot with mine !

Can you keep the original bottom compartment

does this fit 2004 honda accord ex

This is a very detailed and wonderful video. Considering buying a civic so this would be a perfect project to work on.

I have that same head unit i loooove it.

So all my wires are connected correctly. Amp is fine. Bass speaker good, however, now everything plays through the bass speaker. None of the car speakers work. Uhm so what happened? I have a 2005 honda civic. Help. Pppllleeaassee

No shrink tubing?

The wire that you're holding at 10:43, does it have to be connected? the aftermarket stereo i have doesn't have a port for that wire. thanks

@ProvoBeastAudio

7 жыл бұрын

That is the antenna wire, for AM / FM. Not necessary, you just won't receive a radio signal.

hey, I am hoping for some help here. I accidentally disconnected the wiring harness that was connected to factory wiring..i wasn't thinking and was in a rush. I need to know exactly which wire connects where..since the owner before me had after market harness installed, the wires are not color codded anymore. I have looked up diagrams, but somehow all of em have one or two colors wrong. Two of the fuses for "acc radio" have blown. I would really appreciate some help if possible, i suck with wiring.

@ProvoBeastAudio

8 жыл бұрын

Locate the ACC radio fuses and replace them, located possible both in the cabin of the civic as well as under the hood. Secondly, online wiring diagrams are good, but to be safe, you can always test with a multi meter before you hook things up.

Would illumination work properly if you wire the orange (illumination) to orange and white (also illumination) wires together between the car adapter and radio harness, respectively, on a 2003 Civic and Sony MEX-GS810BH? Does it matter they're different colors?

@ProvoBeastAudio

7 жыл бұрын

If your harness doesn't support a orange and white wire, then yes, that should be just fine.

Thanks for the video, however the unit still cuts out when I drive over bumps no matter how big. Do you have any recommendations for better stability in the dash? I think it could be a wiring issue as well.

@ProvoBeastAudio

7 жыл бұрын

Sounds like you have shorts in the dash. Double check all connections as this will fix the cutting out issue.

did this successfully the only problem i got is a whining noise from the speakers whenever i rev the car. any possible solution?

@ProvoBeastAudio

5 жыл бұрын

Sounds like a bad ground. Be sure to clean paint off and fix your grounding point.

hey I have a question so my question is I have an aftermarket stereo in my car and well I want to replace it with another aftermarket stereo so will i need to buy another wiring harness or i could use the one in already

@ProvoBeastAudio

5 жыл бұрын

It all depends on how your current aftermarket radio is installed. I can't answer that question until you pull the current radio out to see if it was wired correctly and if any of the current parts are reusable.

so do I need the mic to hook up my phone to Bluetooth I'm thinking of buying so I don't need a aux cord had dealing with the wiring

@ProvoBeastAudio

7 жыл бұрын

If you want the other party on the line to hear you, you will need a mic. But to stream music, it is not needed.

I have a 2003, the guy i bought it from had removed the factory harness so now i have to crimp each separate wire and have had no luck finding an actual wire colour code/diagram that isnt misleading. wondering if you could help with that, thanks

@ProvoBeastAudio

7 жыл бұрын

Hopefully this helps! www.modifiedlife.com/car-stereo-radio-wiring-diagram-2003-honda-civic/

Would be the same with an 04 civic hybrid? Or are there certain hybrid components that would alter the process?

@ProvoBeastAudio

6 жыл бұрын

Yep, should be just the same.

Can you adjust the shade of blue of the Pioneer head unit to match the blue of the dash lights inside the 04 Civic?

@ProvoBeastAudio

7 жыл бұрын

Nope, it's fixed from the manufacture.

if I already have a after market stereo do I still have to take everything apart to replace it with a newer one??

@ProvoBeastAudio

7 жыл бұрын

Depends on how they installed the previous stereo in your civic. Give it a shot

hey great video just a question i have a 2003 acura el 4 door when i install the new stereo do i need a serial number or a code cuz my car has a anti theft system

@ProvoBeastAudio

6 жыл бұрын

No the code is just for the factory radio.

Had my stereo stolen last week so I ordered a replacement. The thief left that metal frame on the factory radio in the car, do I have to remove that before putting the new one in? Also, where do I attach the ground wire to?

@liveandletlive2894

5 жыл бұрын

I would guess yeah

would this work the same if I'm installing the kenwood KDC-BT362U?

@ProvoBeastAudio

8 жыл бұрын

+talya cristofoli Yes, being also a single din, it would be identical for the install.

What do I do if we cut off completely all the wires on the harness that comes with car I need help please

@ProvoBeastAudio

6 жыл бұрын

Oh boy, you've created a mess then. Either reattach the factory harness and use the adapter like the video, or you have to manually wire in your new harness using this diagram: www.modifiedlife.com/car-stereo-radio-wiring-diagram-2003-honda-civic/

Is it easy

Where does the red cable go? Because on my harness it doesn't come with a red cable. Please help. Thank you

@ProvoBeastAudio

7 жыл бұрын

The red wire? This is your ignition wire, or the wire that triggers your radio to turn on when you start your car. It is a necessary wire and will be required for your install.

What is the tool called you used to remove the panels without messing them up?

@ProvoBeastAudio

8 жыл бұрын

+Tyler Martens Panel trim removal tools

2 Questions, I'm about to install a Kenwood deck and I noticed on 2:12 of your video you put the dark blue wire in with the red one, I'm also using a metra wiring harness and the Kenwood harness is pretty much identical to the Pioneer harness you're using and doesn't have a matching blue wire. What is the reason for putting the blue and red wire together? I'm pretty sure I'm gonna do the same thing, I'm just wondering your reason for doing this. Also, on the Kenwood deck, like the pioneer deck it has the blue wire with white stripe.. if that doesn't appear on the wire harness I got from Metra, it just stays left in its sleeve, correct?

@dballin2

7 жыл бұрын

Also, my deck has a brown wire that's used for muting purposes, do I just leave that alone or does it need to be combined with another wire also?

@ProvoBeastAudio

7 жыл бұрын

The blue wire is the power antenna and the Pioneer doesn't have a power antenna wire. So commonly, it is easiest just to tie the power antenna wire in with the ignition wire to gain power when the key is on.

@ProvoBeastAudio

7 жыл бұрын

Just tape off the muting wire, you will not need it.

Do I have to buy a second dash bezel or can I just put the radio in the old one

@ProvoBeastAudio

7 жыл бұрын

You can pull the radio in the old one, but it will leave gaps around the radio since they are not identical sizes.

Is the dash kit necessary? The pioneer deck seems like it'd fit in the standard deck slot.

@ProvoBeastAudio

7 жыл бұрын

It would, but it would leave gaps between the dash bezel and radio. If you don't mind the gaps, you can use the factory slot without the kit.

hey great video just a question if i buy a dash kit does it come with a wire harness

@ProvoBeastAudio

6 жыл бұрын

90% of the time, no, unless you buy it as a bundle online.

do you have the link to buy everything include the radio and the tool you use in the video ? thanks

@ProvoBeastAudio

8 жыл бұрын

+Thang Bui I do not, links always change. See the description for all the parts used in the video, then search those parts in amazon. The tools i used are crimpers, wire strippers, phillips screw driver, panel removal tools, 10mm socket wrench, butt connectors. That should be all you need.

Ca you just switch the Radio without putting new harness in ?

@ProvoBeastAudio

7 жыл бұрын

It would require you to cut the factory harness and label colors manually. A harness adapter is only a few dollars and will save you a lot of time and effort in the end. Totally worth the purchase.

Would this work for a pioneer DEH-150 MP?

@ProvoBeastAudio

7 жыл бұрын

It sure would.

I have been working on a similar install, but I can't get my radio sleeve to stay secure in the kit. Did you get yours to stay flush and completely secure?

@ProvoBeastAudio

7 жыл бұрын

Yep, you will need to ensure you bend the tabs out on the metal sleeve to ensure it stays secure in the dash kit.

@banner290

7 жыл бұрын

I can't seem to get the tabs to bend in a way that fully secures it in the kit... what should I do to fix this?

@ProvoBeastAudio

7 жыл бұрын

Get creative, hot glue works wonders too

Thank you bro

Would this work for pioneer mxt-2969bt

@ProvoBeastAudio

7 жыл бұрын

Yep. It will fit that model pioneer fine!

So any Pioneer Single-din In-dash Cd Receiver would work ?

@ProvoBeastAudio

7 жыл бұрын

Yep!

Do you need a Dash kit? Can I just put the new radio right into where the old one was?

@ProvoBeastAudio

6 жыл бұрын

You could get by without a dash kit, but it may not fit perfect (leaving gaps around the radio). If you are cool with it, go for it.

Hey I just have a question. I just bought a 2004 Honda Civic Si and there is already an aftermarket deck in there but I want to put my kenwood deck in there. Is it safe to assume that those safety 8mm bolts are removed and I can just pry the dash out without removing screws?

@ProvoBeastAudio

7 жыл бұрын

Generally yes, but be careful, just make sure they are not in there to reduce the risk of cracking the dash bezel.

I really need to know, does this head unit sound good?? I got my car used and the previous owner installed a Kenwood kdc bt562u head unit which sounded way worse then the stock head unit. It made the stock speakers sound like tin cans. I really want a new head unit but am worried about sound quality after my experience with the Kenwood. Any suggestions?

@ProvoBeastAudio

6 жыл бұрын

I'm a pioneer fan, sure, but it is all in the ears of the beholder. This unit specifically puts out 14 watts rms per channel which may be a hair more than your factory radio, but it also allows you to make some EQ adjustments the factory radio will not allow. It's your call, but generally i've seen greater improvements.

@BingermanAlley

6 жыл бұрын

Provo Beast Audio Installation Thanks!

@BingermanAlley

6 жыл бұрын

Back when I had that head unit In my car I didn't know how to EQ so I might try it again before getting a pioneer.

I wire everything color coated bought spare fuses checked the fuse box for burnt fuses yet my stereo won’t turn on wtf I’m I doing wrong lol

@riverhoneybee

5 жыл бұрын

fernando escobedo possible you have a short somewhere. Recheck wires and connectors.

do you need to have the Bluetooth mic I dint quite understand that part

@ProvoBeastAudio

7 жыл бұрын

You don't need the bluetooth mic, but if your radio is bluetooth compatible, in order for hands free calling and the other end to hear you, you will need a mic. But again, the mic is optional.

will the JVC KD-R680S work with the kit?

@ProvoBeastAudio

7 жыл бұрын

Yep, as any standard single din radio.

Will the pioneer DEH-X4900BT fit in this kit?

@ProvoBeastAudio

7 жыл бұрын

Sure will!

Would this work for a boss 508UAB?

@ProvoBeastAudio

7 жыл бұрын

Yep!

Do you have to purchase a Bluetooth mic to play music off your phone? Or purchase an aux cord?

@ProvoBeastAudio

7 жыл бұрын

The bluetooth mic is only needed for bluetooth calling as it acts as the mic for those on the other end to hear you. Not necessary for streaming music via bluetooth from a phone. You will need to purchase an aux chord as these radios do not supply them.

ur a beast bro thanks

Hi when installing the new radio .... Did you need a antenna adapter if yea what kind did you use

@ProvoBeastAudio

8 жыл бұрын

The description has all the details, no, there is no antenna adapter required.

@garcia2886764

8 жыл бұрын

Thank you very much

Does it matter what color but connecters I use

@ProvoBeastAudio

4 жыл бұрын

Yes, as the color indicates size. Usually red size connectors match the size requirement of the radio wiring.

Good work. My brother love it. Blessed be the most high God name.

Is there a turorial on the touchscreen one?

@ProvoBeastAudio

6 жыл бұрын

We don't have one, but a double din will fit fine as well, everything will be the same except for the dash kit needed, it requires the Metra 95-7899 kit. Same wiring harness and choose your double din radio.

My pioneer deh 9800bt is broken and i want to replace it with different stereos, is there any cables needs to do to replace the subwoofers?

@ProvoBeastAudio

7 жыл бұрын

If you are just swapping out radios, your amp / sub system will be able to plug into the new radio, just as it is connected to the old.

so i'm at a loss, i got to the part where you are suppose to be able to remove the whole thing but it won't budge, i have the right tools, is there another way to get these off?

@ProvoBeastAudio

8 жыл бұрын

+Collin McRae If you got the security screws out from underneath (there are two of them), then the rest is held on with clips. Without damaging the dash area, carefully pry out the whole radio bezel and it should technically pop free. Good luck to ya!

@CollinBoddy

8 жыл бұрын

Thanks, I got that far. But how do you wire up the radio?

@ProvoBeastAudio

8 жыл бұрын

+Collin McRae Match the colors up from the adapter harness to the new radio harness. I have a video on my channel that will walk you through on how to wire up a harness. That will help you out.

What gauge wire is the wiring harness? Trying to find this info so I can buy the right size wire strippers.

@ProvoBeastAudio

7 жыл бұрын

It is about 18 gauge.

@dlee6985

7 жыл бұрын

Im installing a DEH-X4900BT (the newer model of the 4800 in your video) in my 04 civic and the harness has an orange/white dimmer wire but the metra harness only has a solid orange illumination wire. What should I do with these wires??

@ProvoBeastAudio

7 жыл бұрын

The purpose of the dimmer wire is to dim the display on the radio when the head lights are on. Essentially, the voltage changes on the dimmer wire when the headlights are turned on. If that illumination wire performs that same function, go ahead and connect that wire with the pioneer's orange and white wire.

Where do you purchase the kit for the radio

@ProvoBeastAudio

5 жыл бұрын

Internet is your friend

What kind of radio you put instead ?

@ProvoBeastAudio

8 жыл бұрын

+miller I don't understand what you are asking...if you are asking what type of radio I used, it is in the title of the video..

Do you have to use that exact wiring harness? I can't find it anywhere

@ProvoBeastAudio

8 жыл бұрын

Walmart, Best buy, amazon, ebay all carry them. Just google Metra 70-1721. Its actually a very common harness. Hopefully that helps.

@itsBirdy2

8 жыл бұрын

+Provo Beast Audio Installation It helped... I found them! Thanks

is civic IMA the same procedure

@ProvoBeastAudio

7 жыл бұрын

Sure would be!

if i were to get an aftermarket stereo do i have to get the kit? or will the stereo just fit if i just take out the stock stereo and replace it with the aftermarket?

@ProvoBeastAudio

8 жыл бұрын

+aycy10 You will need a dash kit. There are different types depending on the brand. Regardless, you will need it.

@taeyeung007

8 жыл бұрын

+Provo Beast is it because the stock stereo doesn't come out as an individual so i need a kit?

@ProvoBeastAudio

8 жыл бұрын

They are not the same size, it won't be a direct swap, but you could use the factory bracket but it would leave gaps around the radio. If you have a pocket below the radio, they are separate as shown in the video, but it isn't a perfect swap.

@taeyeung007

8 жыл бұрын

+Provo Beast ohhhhh alright, thanks for all the help ! ill order the kit from the link u shared in the description.

is it the same process for an automatic ??

@ProvoBeastAudio

8 жыл бұрын

+vanessa mata sure is.

how did you do the wiring??

@ProvoBeastAudio

7 жыл бұрын

It shows at 1:10 in the video.

Why didn’t you throw a double din deck in

do I need the mic to play or connect my phone to bluetooth

hi I just got a honda 2004 civic and when I got it the radio front was gone I'm planning get a subwoofer should I just get a new radio or try find a front piece

@ProvoBeastAudio

8 жыл бұрын

What do you mean by "front piece"? Are you talking about the face plate to the existing stereo? If so, its worth just replacing the radio to something newer. It would be more reliable to do so.

@peacewinwar

8 жыл бұрын

K I was wondering if a dual xr 4120 would work with my Rockford single 12 inch sub

@ProvoBeastAudio

8 жыл бұрын

Be carefull when using the Dual radio products. When customers have asked me to put those in, i have always had to replace them for the customer months later because the sound quality is terrible. The rockford fosgate is a good choice.

@peacewinwar

8 жыл бұрын

+Provo Beast Audio Installation can u tell me a good radio for my civic then under 50

@ProvoBeastAudio

8 жыл бұрын

Pioneer DEH-150MP

can you use aux cord with it

@ProvoBeastAudio

6 жыл бұрын

Yes, there is an AUX input on the front of the radio.