I like to loop a couple zip ties together to make a big circle and hook it under the connector of the coil as far back and close to the coil body as possible, then I can apply steady upward force as I work the back part up with my fingers. Works every time with zero drama.

@user-hc9sk3mg1h

Жыл бұрын

Genius initiative. I'll give this a shot.

Thanks so much. Never heard the explanation about the pick tool AND the fact that ALL FOUR connectors can't be disengaged simultaneously! My first Knipex purchase arrived just before Father's Day. I'm very happy with these Twin Grips! Thanks for promoting them over the years. You inspired me to buy them.

Big big thank you! This video saved me in a village far from any cities. Car was frozen and only replacing hot coils helped me to start the engine

nice straightforward video. I always use a small prybar as well. But, I also add a small dap of dielectric grease to the coil prior to installation. These 2.0L TSI engines are some of the easiest for sparkplug changes.

I highly recommend magnetic spark plug sockets helps a lot if you have oily plugs

Cool change with the background music. I’d love to see you change auto transmission fluid on a B8 A4

Very nice idea to unclip the connector.. I tried.. And succeed in a minute or two✌ kudo my dear 💕

Here's a fun tip. Should the boot tear, you have to buy a coil to get the boot.

2 of 4 good enough for government work. 🤣😂🤣😂

I’m going to replace the plastic cover to the hardness when I rebuild my engine; hopefully this summer. And also put in new coils; I got some cheap ones in there from autozone.

Gotta have a good set of picks working on these

If all my clips are broken can that cause a multiple misfire p0300. I’ve changed coils plug’s injectors chasing this misfire. I have a lot of carbon buildup wondering if that could be it too.

I followed this video as well as looked into 25 others and forums as well. The connector cracked where I tried to pry with the pick and still won’t disengage from the coil pack.

Hey i have an Audi a4 2009 can you please make a video of how to Change the lifters of the Audi please thanks

Hey naptown....I need help rebuilding my 2.0tfsi 2009 audi engine. I live in Wisconsin... help?

Those spark plugs are pre gapped but you didn’t check if gap was correct? I bought same ones and 1 spark plug had a gap of 0.40 not 0.32

one of my ignition coils wont go all the way down is there anynone that can help me?

You have a B8 water pump install vid you can link ?

More ccta content please

2014 2.0t cylinder 1 is the first on left?

Is there a way to contact you directly?

Anyone know what the plug gaps are for 2.0t fsi? I’m getting ready to change them in mine and I know they’re pre-gapped from the factory but I’d like to check them for peace of mind

@zzzzzzzsssss

11 ай бұрын

0.032

Do you have any tips what way to get a clip on a rattling waste gate arm on my A5? It's between the turbo and the engine block, so I can't reach in between .... maybe from the bottom, the next time I got it in my friend's shop. Replace the coils, ignition cable holder and connectors since they were too brittle to my taste.

I used a hard wire 0.5 mm instead

@10:04 😂

What are the torque specs for plugs? 21 ft/lbs?

@biz4twobiz463

2 жыл бұрын

yes, between 18 and 22 ft-lbs

@deanakeller2244

Жыл бұрын

And I just did my GTI's Valve Cover Gasket, Spark Plugs, and Ignition Coils. Legit Info on that site!

Hi, when it's necessary to change the ignition coil?

@NaptownTuner

2 жыл бұрын

Every 100k miles or less only original equipment or equivalent

@miguelruvalcaba4260

2 жыл бұрын

@@NaptownTuner thanks for answering me

Hello, please buy special tools for remove ignition coil. It is cheap tool.

@NaptownTuner

2 жыл бұрын

If I had it I’d never use it.

@user-yl1zp5kp5k

2 жыл бұрын

@@NaptownTunerHave a nice day!