Disassembly and Reassembly of the '81 = '83 Virago xv750 Carbs. Two bad carb sets combined into one good set of carbs
Жүктеу.....
Пікірлер: 94
@panch782 жыл бұрын
I was able to easily rebuild my carbs with these instructions. I really appreciate your videos. Thank you!
@fritzramirezjr8144
Good knowledge to rebuild the carbs. I'm about to do the same.
@chiefpepdesign4 жыл бұрын
Really good video! Way more detailled than mine. Props! Happy to see some more Virago enthousiasts video's here on KZread! 👍
@dancomden65773 жыл бұрын
Super helpful, thanks. I am rebuilding the carbs on my '81 this weekend and this was great!
@guerosern4 жыл бұрын
Great video, I have watched it three times now just to see if I didn’t miss anything . I just bought my first bike 83 midnight-special ,the carbs off it . I took everything apart to clean it good .only thing I saw missing was a bowl drain screw ,and one intake manifold.
@surefiremushroomsmicrogreens4 жыл бұрын
You the man 🤘👍 Thank you!!!
@lucasazeredo1 Жыл бұрын
Hey mate, thanks for all the knowledge! I wonder if you could direct me to find a picture of a assembled throttle cable linkage as I think mine is installed incorrectly by the previous owner of the bike I just bought. when I pull the cable it doesn't move if I try with my hands it's really hard to pull up the throttle but if I move the left linkage it moves freely, is there some installed incorrectly? would appreciate some input mate. Thanks in advance
@scottantonides9209
Hey Steve! great video. I'm replacing the diaphragms on the same carbs and I'm looking for a good way to attach and seal the diaphragms to the barrel. The aftermarket diaphragms don't come with the plastic ring. Is there a gasket sealer that works?
@christopherathey5944 Жыл бұрын
Hi Steve ,. Have you got a video of the oil pump sprocket install on to the tapered shaft of a xv1000/750.
@jumar3603 жыл бұрын
Awesome! Thajks
@curtis888014 күн бұрын
Hey Steve, I just recently got a 82 XV920 and has the same carbs. Do you know of any place to get those air filters on the carbs or any way to replace the internals? Mine are all deteriorated.
@demijoker41604 жыл бұрын
Where you find the Manuel's I tried to find torque settings for the carburetor in my 82' Virago
@rp4160 Жыл бұрын
How do you remove the rubber diaphragm from the slide? I’m trying to replace it with a new one
@brenbuchler942 жыл бұрын
Hey Steve! Working on a 1983 Virago 920. I am doing an overhaul on the carbs and a bit confused on the correct placement of the air jets in the top of the carbs under the choke tube. I noticed in your video the larger main air jet is on the engine side and the pilot on the airbox side. I saw another rebuild video and looking at a verison 1 hitachi hsc40 diagram it looks like the main air jet is on the airbox side and the pilot on the engine/butterlfy side. Can you provide any clarity? Your videos have helped me a ton so far!
@automech014 жыл бұрын
Im doing mine right now could you tell me which emulsion tube went to which carb. mine has to different tubes. 1 has 4 and 2 holes and the other has 3 and 2 holes?
@Horner1814 жыл бұрын
On the virago 750 the front manifold gasket has two ports one goes to the t vacuum line but where does the other go to? Or should I put a plug on it like the back one?
@wademowers37824 жыл бұрын
When you have fuel in your oil. Is that from a leaking seat? Or is it the needle on these carburetor's? Or am I just completely wrong? Any info is appreciated. Thanks.
@ridingthemidwest12222 жыл бұрын
I’ve been struggling with getting the little ports clean on the actual bowls of the carbs I’ve tried wire, tiny drill bits carb cleaner and air, everything else on the carbs went good nothing was too dirty but I’m out of ideas on those bowls any input would be great!
@williamhart23443 жыл бұрын
How do you find screwdrivers that will properly fit in your jets? Having difficulty, especially for the jets hiding in the top of the carb. Thank you Steve!
Пікірлер: 94
I was able to easily rebuild my carbs with these instructions. I really appreciate your videos. Thank you!
Good knowledge to rebuild the carbs. I'm about to do the same.
Really good video! Way more detailled than mine. Props! Happy to see some more Virago enthousiasts video's here on KZread! 👍
Super helpful, thanks. I am rebuilding the carbs on my '81 this weekend and this was great!
Great video, I have watched it three times now just to see if I didn’t miss anything . I just bought my first bike 83 midnight-special ,the carbs off it . I took everything apart to clean it good .only thing I saw missing was a bowl drain screw ,and one intake manifold.
You the man 🤘👍 Thank you!!!
Hey mate, thanks for all the knowledge! I wonder if you could direct me to find a picture of a assembled throttle cable linkage as I think mine is installed incorrectly by the previous owner of the bike I just bought. when I pull the cable it doesn't move if I try with my hands it's really hard to pull up the throttle but if I move the left linkage it moves freely, is there some installed incorrectly? would appreciate some input mate. Thanks in advance
Hey Steve! great video. I'm replacing the diaphragms on the same carbs and I'm looking for a good way to attach and seal the diaphragms to the barrel. The aftermarket diaphragms don't come with the plastic ring. Is there a gasket sealer that works?
Hi Steve ,. Have you got a video of the oil pump sprocket install on to the tapered shaft of a xv1000/750.
Awesome! Thajks
Hey Steve, I just recently got a 82 XV920 and has the same carbs. Do you know of any place to get those air filters on the carbs or any way to replace the internals? Mine are all deteriorated.
Where you find the Manuel's I tried to find torque settings for the carburetor in my 82' Virago
How do you remove the rubber diaphragm from the slide? I’m trying to replace it with a new one
Hey Steve! Working on a 1983 Virago 920. I am doing an overhaul on the carbs and a bit confused on the correct placement of the air jets in the top of the carbs under the choke tube. I noticed in your video the larger main air jet is on the engine side and the pilot on the airbox side. I saw another rebuild video and looking at a verison 1 hitachi hsc40 diagram it looks like the main air jet is on the airbox side and the pilot on the engine/butterlfy side. Can you provide any clarity? Your videos have helped me a ton so far!
Im doing mine right now could you tell me which emulsion tube went to which carb. mine has to different tubes. 1 has 4 and 2 holes and the other has 3 and 2 holes?
On the virago 750 the front manifold gasket has two ports one goes to the t vacuum line but where does the other go to? Or should I put a plug on it like the back one?
When you have fuel in your oil. Is that from a leaking seat? Or is it the needle on these carburetor's? Or am I just completely wrong? Any info is appreciated. Thanks.
I’ve been struggling with getting the little ports clean on the actual bowls of the carbs I’ve tried wire, tiny drill bits carb cleaner and air, everything else on the carbs went good nothing was too dirty but I’m out of ideas on those bowls any input would be great!
How do you find screwdrivers that will properly fit in your jets? Having difficulty, especially for the jets hiding in the top of the carb. Thank you Steve!
Could I apply this to rebuilding the xv920 carbs