This is my fathers car and they did an amazing job. We can’t say enough good things about them! Thanks guys

@backroom12

10 ай бұрын

How much was the install back then

Thanks for the video, helped me out a lot when I did mine today. Only thing I found vs your video was that it was better for me when doing the outside piece, from the seam to the outside of the car, to start in the middle top (right along the seam) and slowly working outward front to back and down the middle and then finally to the rear quarter section, then onto the a pillar last. Thanks again.

Did This for a living back in the 80's about 25 to 35 tops a week ...When doing the rear quarters which always is the hardest part because of rinkles.. Use a Heat gun to warm up the vinyl in that area first then (pass.side)at 5:57 his body is in good position but with your left hand get a good grip and pull down with a constant hard pull and to the left and at the same time with palm of right hand smooth down from the top corner of rear window to bottom of body of car and to the left along the edge.. ahh what the hell I'll just come by and show ya ...LOL... good Luck

@theofficialdjfresco3004

3 жыл бұрын

Do you know anywhere in the tri state area that can still do this , I have a 86 Mercedes 190 ?

@vinylvishrecords

3 жыл бұрын

@@theofficialdjfresco3004 Sorry Don't know of any places anymore and My friend that I worked with was still doing Tops on the side but just recently died. I don't think they made vinyl tops for those cars unless it was the one and only one I did...haaaaa

@vinylvishrecords

3 жыл бұрын

oh god, I cringe when I watch this Video, I just want to jump through the screen and do it for them..haaaaaa

@challenger-rta3761

2 жыл бұрын

Would it be advisable to try to remove wrinkles or bubbles,With a steamer iron before installing the top? Your opinion is appreciated!

We used to set 3 or 4 hundred a day on the line. there were four guys setting the top and two guys trimming it. The car was sprayed up the line and the underside of the vinyl top was sprayed ahead of time off line on sub assembly line ten at a time

@1967davethewave

3 жыл бұрын

That's pretty incredible. The high production of an assembly line and yet they all come out looking really good.

@kadenkylo4448

2 жыл бұрын

you probably dont care at all but does anyone know of a trick to get back into an Instagram account? I stupidly lost the password. I appreciate any help you can offer me.

@grantomar7106

2 жыл бұрын

@Kaden Kylo Instablaster :)

@kadenkylo4448

2 жыл бұрын

@Grant Omar i really appreciate your reply. I got to the site through google and Im in the hacking process atm. Looks like it's gonna take a while so I will get back to you later when my account password hopefully is recovered.

@kadenkylo4448

2 жыл бұрын

@Grant Omar It did the trick and I finally got access to my account again. I am so happy:D Thanks so much, you really help me out !

True skill , not to many can do anymore 😢

thank you for the good info, beautiful Charger by the way!

I had a '70 Charger R/T with the VIG years ago,an expensive top to replace today.

good job

how about a 1970 challenger vinyal top with rear window plug?would like to know how to see how you cover plug seams?

Great video, Like & Subscribed! I've never seen this alligator vinyl, before, it's beautiful! Was this available from the factory in white, too? Was the alligator available in 1969, as well? Got any links to period material that mentions this? Thanks, again, great video!

When i disassembled my 69 chargers drip edge moldings, the original vinyl material did overhang on the drip edge. There was clearly a good 1/8 to a 1/4 inch of the original vinyl material under the drip moldings and they were clamping down on the vinyl all along the edge. So it'd be interesting to know how they did it in this video, where does the vinyl end along the drip edge exactly? There's also a clear size difference in the original trim and the reproduction trim. Must be a new way of doing it?

Do you all take in cars to install a vinyl roof on?

Nice job. Being an automotive trimmer by trade, I would suggest both men should be wearing respirators. Glue fumes can be nasty.

I see they sprayed glue on top. But nothing was covered for over spray. Won’t damage the paint?

How are you not getting glue all over the dash??It should be covered.

@chadlipton1745

6 жыл бұрын

brock007football Yep that stuff slings everywhere. I bet it's all over the dash and red paint too!

Where can I get the vinyl done on my grand marquis?

Vinyl top=rust trap

Initial Prep: I hope that wasn't 2-pack clear you were sanding? (two-part urethane). Big health risk sanding 2-pack without at least a gas mask, and ESPECIALLY using air to blow off! No safety goggles either. Eye protection should always been worn when the risk of flying particles exists. This video is a poor example. A full respiratory system is recommended with urethane , even when dry sanding and at least a gas mask or strap on particulate filter, even for the old acrylic paints. These DIY videos are rife with poor personal safety and big names like you should be leading the pack with correct safety examples so that the mass of ignorants (no that's not a spelling mistake) will hopefully follow your example

@andrewarmstrong7310

4 жыл бұрын

I drink urethane for breakfast, lunch and dinner and fart methane.

@McClellan71

3 жыл бұрын

Thanks for the book Sally!