1964 - 1967 Chevelle GM A-Body Wilwood Front Disc Brake Install

Detailing the set-up and install of Wilwood's 67 Chevelle Front Disc Brake Kit.
Wilwood Part #: 140-10996-DR
Link to the kit used: www.wilwood.com/brakekits/Bra...
Music | "Sweet" by LiQWYD
Watch: • LiQWYD - Sweet [Official]
License: www.liqwydmusic.com/how-to-use
Download/Stream: hypeddit.com/link/un7fp7

Пікірлер: 59

  • @e8zy_e
    @e8zy_e Жыл бұрын

    The simplest video out thanks ‼️

  • @mgs2rx
    @mgs2rx4 ай бұрын

    Be sure to check your valve stems for clearance if they are inside the wheel. There are low-profile stems available.

  • @midatlanticcustoms

    @midatlanticcustoms

    4 ай бұрын

    Good note!

  • @devicetrickz
    @devicetrickzКүн бұрын

    Where did you get the suspension kit with the spindle and everything I'm looking to get my front suspension set up with control arms before installing this kit

  • @devicetrickz

    @devicetrickz

    Күн бұрын

    Also will stock suspension work with this kit or did you have to Frankenstein a bunch of pieces together?

  • @midatlanticcustoms

    @midatlanticcustoms

    Күн бұрын

    The suspension kit is from UMI. It is their GM A-body Stage 2 kit. Summit sells the spindles.

  • @midatlanticcustoms

    @midatlanticcustoms

    Күн бұрын

    Yes, stock suspension will work with this kit.

  • @midatlanticcustoms

    @midatlanticcustoms

    Күн бұрын

    www.umiperformance.com/home/product/1964-1967-gm-a-body-handling-package-stage-2/

  • @midatlanticcustoms

    @midatlanticcustoms

    Күн бұрын

    www.summitracing.com/parts/sum-ck1000-1/make/chevrolet/model/chevelle/year/1967

  • @Macnificent78_
    @Macnificent78_ Жыл бұрын

    Great video bro very detail i love it ? Did you have the cut the spindle due to i think i might have the cut mine 78 inpala landeu

  • @midatlanticcustoms

    @midatlanticcustoms

    Жыл бұрын

    Thanks! Nope, did not have to cut the spindles

  • @Macnificent78_
    @Macnificent78_10 ай бұрын

    Did you run a washer and shim you front of the bolt ??? If so did that help with the spacing for the brake pads????

  • @midatlanticcustoms

    @midatlanticcustoms

    10 ай бұрын

    Yes we did run a shim, but it didn't change the brake bad mounting

  • @Macnificent78_
    @Macnificent78_ Жыл бұрын

    Did yo have to Modify the spindle great video I have the same set up I wish I could find a video for my b body

  • @midatlanticcustoms

    @midatlanticcustoms

    Жыл бұрын

    Thanks! Nope, this is factory style spindle and no modifications required. Just can't run anything smaller than 15" wheel with this set-up. Some 14" may work.

  • @dewaynemitchell3931
    @dewaynemitchell3931 Жыл бұрын

    Hello im doing the same exact set-up got a quick question do you use red or blue loctite for each set up such as the bolts for the hub as well as the adapter plate and rotor

  • @midatlanticcustoms

    @midatlanticcustoms

    Жыл бұрын

    Things that you won't be servicing regularly (wheel hub adapter brackets, spindle bolt nuts, etc) you can use the red loc-tite. The other serviceable items (caliper bolts) it's best to use blue loc-tite. Hope this helps.

  • @dewaynemitchell3931

    @dewaynemitchell3931

    Жыл бұрын

    All man thanks for the quick response that helps alot been watching your video step by step and it's helping alot yours is the best I've seen on KZread that even i can understand appreciate it👍

  • @midatlanticcustoms

    @midatlanticcustoms

    Жыл бұрын

    @@dewaynemitchell3931 thank you for the support, and glad the videos are helping! The feedback is greatly appreciated

  • @dewaynemitchell3931

    @dewaynemitchell3931

    Жыл бұрын

    ​@@midatlanticcustomsgot another quick question if you can help on the black rotors it's an arrow on each of them if you're facing them one would be going clockwise and the other counter clockwise so would the clockwise arrow go on the passenger side rotor and the counter clockwise go on the driver's side right

  • @midatlanticcustoms

    @midatlanticcustoms

    Жыл бұрын

    @@dewaynemitchell3931 yes, that would make sense. I've seen different companies set it up in different ways. What is the part # for the kit you are installing ?

  • @Macnificent78_
    @Macnificent78_10 ай бұрын

    One pad had a lil play on 1 side is that going to be a issues for me and when i add more shim to fill the gap the other was tight but here the thing they go in nice i just have a lil play

  • @midatlanticcustoms

    @midatlanticcustoms

    10 ай бұрын

    A little play shouldn't be an issue, as long as it isn't excessive

  • @Macnificent78_

    @Macnificent78_

    10 ай бұрын

    @midatlanticcustoms ok thanks I was a little worried

  • @Macnificent78_

    @Macnificent78_

    10 ай бұрын

    @@midatlanticcustoms great video very detailed that helps alot

  • @Macnificent78_
    @Macnificent78_ Жыл бұрын

    Did you run the same stud or did you go longer???

  • @midatlanticcustoms

    @midatlanticcustoms

    Жыл бұрын

    Same studs

  • @user-hs8qj2fi9y
    @user-hs8qj2fi9y16 күн бұрын

    What spec master cylinder bore size etc ?

  • @midatlanticcustoms

    @midatlanticcustoms

    15 күн бұрын

    Details on disc brake kit: www.wilwood.com/brakekits/BrakeKitsProdFront?itemno=140-10996-DR We're using wilwood's master cylinder with this kit. You can check them out on their website above.

  • @lawrencer588
    @lawrencer5885 ай бұрын

    those look like the rear calipers not the front set. is that right?

  • @midatlanticcustoms

    @midatlanticcustoms

    5 ай бұрын

    This is definitely the front set. Wilwood produces these so you can mount them on either side of the spindle, depending on your set-up. We just mounted them on the fwd side vs the rear.

  • @lawrencer588

    @lawrencer588

    5 ай бұрын

    @@midatlanticcustoms thanks for the quick response! I'm helping a friend, just got the instructions, had him send me links to what he ordered so i can sort rear from front. noticed the front has smaller pads but four pistons but the rear has unusually larger pads with only 2 pistons.

  • @midatlanticcustoms

    @midatlanticcustoms

    5 ай бұрын

    Yeah, I would double check part #s. Wilwood makes lots of different variations of these, and it's easy to mix them up!

  • @timvincent1968
    @timvincent1968 Жыл бұрын

    calliper bracket on the wrong side ? and bleeders need to go up, caliper on the rear side towards the back

  • @midatlanticcustoms

    @midatlanticcustoms

    Жыл бұрын

    Calipers have bleeders on both ends, so they can be installed in either configuration. The brackets are in the correct orientation. Check the assembly instructions here: www.wilwood.com/BrakeKits/BrakeKitsProdFront?itemno=140-10996-DR

  • @gaslightapparel2443

    @gaslightapparel2443

    Жыл бұрын

    Calipers should be on back side of spindle. Firewall side, not tie rod side

  • @midatlanticcustoms

    @midatlanticcustoms

    Жыл бұрын

    @@gaslightapparel2443 direct from wilwood's manual: "*NOTE: Some applications for this kit have the steering arm to the rear of the spindle and others to the front. Also, some applications have room to mount the bracket and caliper on the steering arm side of the spindle while the steering arm may interfere in other applications. The brackets in this kit may be mounted on either the front or rear side of the spindle."

  • @Macnificent78_
    @Macnificent78_ Жыл бұрын

    What size socket for the studs ???

  • @midatlanticcustoms

    @midatlanticcustoms

    5 ай бұрын

    Don't have it handy, but hopefully you got it figured out

  • @Macnificent78_

    @Macnificent78_

    5 ай бұрын

    Yup I got it thanks

  • @jameshamley5056
    @jameshamley5056 Жыл бұрын

    What is the part number for the hole kit thank you

  • @midatlanticcustoms

    @midatlanticcustoms

    Жыл бұрын

    140-10996-DR

  • @jameshamley5056

    @jameshamley5056

    Жыл бұрын

    Thanks

  • @jameshamley5056

    @jameshamley5056

    Жыл бұрын

    Can't wait to see the car love the chevy have 70 grand prix in process of restoration of it

  • @rojelioochoa918
    @rojelioochoa9187 ай бұрын

    Where you get spindles

  • @midatlanticcustoms

    @midatlanticcustoms

    7 ай бұрын

    Summit has them: www.summitracing.com/parts/sum-ck1000-1/make/chevrolet/model/chevelle/year/1967

  • @ironhidedirtymax7940
    @ironhidedirtymax79405 ай бұрын

    What exact kit was this?

  • @midatlanticcustoms

    @midatlanticcustoms

    5 ай бұрын

    The Wilwood Part # for the kit is: 140-10996-DR

  • @e8zy_e
    @e8zy_e10 ай бұрын

    Nice video but man 😢 did them backwards

  • @midatlanticcustoms

    @midatlanticcustoms

    10 ай бұрын

    Direct from wilwood's manual: "The brackets in this kit may be mounted on either the front or rear side of the spindle."

  • @jameshamley5056
    @jameshamley5056 Жыл бұрын

    Spindle factory or other

  • @midatlanticcustoms

    @midatlanticcustoms

    Жыл бұрын

    We replaced the spindle before we installed this kit. The OEM spindle had a large amount of wear at the bearing interface.