Every video from you means a new feature for me, thank you.

@TonyAlbus

3 жыл бұрын

Hi Reinhold, Thank you, and sorry for future features for you, more is coming :)

@markgreco1962

3 жыл бұрын

Yes Tony has helped DRAIN my pocketbook for a while now. He is very fun to watch. And smart too.

@TonyAlbus

3 жыл бұрын

Thanks Mark! 😁😁👍

Thanks Tony. I haven’t seen that type of meter before very interesting. Regards Chris

@TonyAlbus

3 жыл бұрын

Thanks Chris, yes my thought also when i bought it, and it turns out not to be bad at all, funny :)

I like your smiley face and voice 👌 Thank you brother for new videos

@TonyAlbus

3 жыл бұрын

Thank you, and welcome!

@sunuk1915

3 жыл бұрын

@@TonyAlbus you are always welcome dear 💞

Recently I have sold my old AVO and used my table multimeter. Not very handy, I was looking for an used Fluke. After your test i decided to buy the aneng. Saves a lot of money, thxs.

@TonyAlbus

3 жыл бұрын

You are Welcome and thank you for your comment Jan

Nice Efforts❤

@TonyAlbus

2 ай бұрын

Thank you!

Always very interesting ... much appreciated ... Thank you ..

@TonyAlbus

3 жыл бұрын

thank you too

Nice review and meter! Thanks a lot.

@TonyAlbus

3 жыл бұрын

Thank you!

I really wanted to love this since the large screen would be great in tight area's . However it's not very handy in auto mode and you can't turn that off. I got one of these yesterday and tested it repairing the electrical system on a car. The issue is since it's auto selecting and there is no manual way to set it to voltage testing the delay in auto mode makes this useless for my intended usage . I went to test a fuel pump by attaching the leads into the pumps power pigtail . When the meter is connected it detects the resistance in the wires and starts to measure it. When i turn the key to send power to the pump the meter detects it , lags then only shows the voltage for a split second because the vehicle will only send power to prime the pump for about 1-2 seconds. Not only is the voltage shown for a brief time the delay make it inaccurate as the vehicle is turning off the power by the time it switches over. Why would you build a device to give accurate readings but then force it to depend on an auto mode?

@TonyAlbus

2 жыл бұрын

For your application its indeed better to have a fast old needle multimeter or a little oscilloscope

Thank You sir

@TonyAlbus

2 жыл бұрын

Most welcome

Dear sir, when I want to measure A 12 V amperage, the fuse always blows (factory included 2 A). The instrument is designed to measure up to 10 A, so it is not clear to me what is wrong. Greeting

@TonyAlbus

7 ай бұрын

Please read a bit more about the difference between voltage and current(amps) then it will become clear why you blow your fuse. small give away. current you measure in between the circuit as part of the loop.

Sir can I measured 0 to 20 milliamp in this multimeter

@TonyAlbus

2 жыл бұрын

Yes it can, with a 1mA resolution

It looks like you are a cartoon translator, your voice will be great in that field. Sorry ❤

@TonyAlbus

9 ай бұрын

Thanks!

Do you know this model? VICI(Vichy) VC8145 Dual Display RMS Bench Digital Multimeter

@TonyAlbus

3 жыл бұрын

Hello Tono, i have not had than one on my bench yet.

@dennisqwertyuiop

3 жыл бұрын

have one for years,,,works great

I don't get these meters. The auto feature is a gimmick to me, and the large display hardly shows extra information. The lack of ranges (especially in the current range) and the fact that current is only detected from 20mA makes it useless for electronics. For roughly the same money Aneng has much better meters like the an8009 or the an870. Not having a kickstand, (impossible because the 4mm sockets are on the underside) makes it useless on a bench and there also isnt a probe holder for 1 hand operation. So imho these kind of meters have been designed with so many concessions in usability and functionality just the to have a higher gimmick factor that they are a joke for the more trained user and only appeal to the novice user who doesn't know what to look out for in a multimeter. If I may ask: is this a paid review?

@TonyAlbus

3 жыл бұрын

You are right on all fronts, but it is just different and it will never replace my keithley for sure :)

Not bad for $20 :) I'm guessing its not Cat 3, nor certified though...

@TonyAlbus

3 жыл бұрын

Hi Stephen, don't think so, can't have it all :))