It's easier too put the inges on the van first , especially the bottom one , has you can spin the inge tight with your spanner just stuck on the back nut

@Mevi

6 жыл бұрын

Of course! That's genius. The tiny hole just doesn't allow for a socket. I spent ages just trying to get the bolt to align with the thread on the hinge. your tip makes more sense than the workshop manual, in fact!

Changing one rear door tomorrow so thanks for filming this 👍👍

I need to do this for my van they are bent also and there is a gap at the bottom you can also see daylight through and get your fingers into, worried about security and heat loss. It's inspired me to get stuck in, great idea with the office chair, thanks Mevi.

@Mevi

6 жыл бұрын

The workshop manual had the doors manuovered on some wild, wheeled crane contraption! Mick's idea for the chair was genius. 😄

Thanks for this, it’s been a great help with my door and hinge swap. Got nice glazed ambulance doors on now, replacing my old solid doors with the big old hinges. I owe you a beer.

@Mevi

4 жыл бұрын

Knowing I helped a brother out is payment enough. Great news Nick. 😎👍

Awesome doors now buddy .. look nice straight lines .. that badge will set it off nice

@Mevi

5 жыл бұрын

I still have the old door's badges in a carrier bag somewhere. One day I might stick the word 'maxi' back on. Or maybe not. 😏

Good work mate.

@Mevi

6 жыл бұрын

Hey, thanks mate

(maybe i missed it in you video) but do you know where the door lamp switch is located? (the light sometimes goes on, sometimes not) Thanks in advance for any help.

@Mevi

Жыл бұрын

I don't know for sure. I think it is likely in the lock itself. I've not seen wires going to anywhere else around the back doors. They go into the rear doors through the real pillars. The side door is different, in that power and control to the lock comes through the contacts on the edge of the door. I haven't found sensors to detect the cab door is open. The only switches for the lights are on the lights themselves. I made a couple of videos where I disassembled the rear and cab lights. Their construction is quite simple. I suppose it is possible there is corrosion in the lights, or a faulty festoon bulb. These 2 videos show the lights disassembled. The first for the rear lights, the second for the cab. kzread.info/dash/bejne/o5qeu8x-l9e4p8Y.html kzread.info/dash/bejne/eGeux8Fwe8yro9I.html

Loving your videos, giving me lots of inspiration for my L4 Relay conversion. Quick question, I don't suppose you still have the steel round door buffers tucked away anywhere from when you converted the door hinges? I'm not having much luck finding any anywhere... I'd be happy to buy a couple off you. Cheers, Nick

@Mevi

4 жыл бұрын

Thanks Nick! 😊😊The magnetic bumpers that are on the door, or the ones on the side of the van? The ones on the door went with the doors, I think. The ones on the side if the van are still bolted on the trim. I've not bothered taking them off as it's a wrestle to get the trim off with rusted bolts and those fragile panel clips.

@nickbentley1111

4 жыл бұрын

I think the magnetic bits are the same for each, it’s the plastic surround that differs. It’d be a pain removing yours as you need to access the mounting nut inside the skin of the van. If you see a couple on your travels let me know 👍🏻

@Mevi

4 жыл бұрын

Aah, right. Yeah, they'll be buried under the walls now. I imagine that you could probably macgyver a solution. Have a look at this link. I used this strong rubber coated magnet for mounting a camera on the bonnet, but this might give you some ideas.. Magnet Expert 79 x 53 x 12mm thick x M6 thread Rubber Coated Mag Pad - 10kg Pull ( Pack of 1 ) www.amazon.co.uk/dp/B0058DBAV2/ref=cm_sw_r_cp_apa_i_H9dWDbAMSNYV8

Hey Mevi, great job on the new doors. I’ve just picked some up recently to do mine. Roughly how long did it take you to do them? Wondering if an eve after work is enough or to give myself a day on the weekend. Cheers! 👍

@Mevi

2 жыл бұрын

Me and Mick swapped them in a few hours... Maybe three? It's a while ago now. I swapped 270° for 180° doors, so I had to figure out the different mounting. If you're doing like for like, maybe you'll do it quicker. I'd say to allow more time. Tweaking the door alignment was the most time consuming part, I think. Perhaps you could fit and align one door and then you'll know if you have time to do the second?

@TheAffrojutty

2 жыл бұрын

@@Mevi Nice one 👍 Yeah I had the thought to maybe do the one and see how it goes.

Great video. Did you not have to swap your driver sider door handle/lock since your key won't work in that door anymore?

@Mevi

2 жыл бұрын

I *still* have the entire handle, cables, AND badges from the original back doors. I planned to swap out the door lock at some stage, but haven't had the need. I believe there is no 'coding' required for the locks. Remote locking worked perfectly from the start with the new doors.

I need to replace my drivers side rear door on my Citroen relay, I'm just wondering if there were any electrics on the drivers side door that you had to mess around with and if so was it difficult or was it a case of just plugs?

@Mevi

5 жыл бұрын

Just plugs - they can only connect one way, so that was the really easy bit. The loom terminates in the rear pillar, so look for a door that has the lock and loom with it. Stripping the old door would be no fun at all.... Probably most doors will come ready to hang. Mine also came with the hinges, but not all do. All the hinge adjustment is in the bolts attaching the hinge to the van.

@huwjones7468

5 жыл бұрын

@@Mevi what do you mean by the loom?

@Mevi

5 жыл бұрын

The loom is what a cable assembly is called. It'll be a few cables with plugs at each end.

@huwjones7468

5 жыл бұрын

@@Mevi wicked thanks!!

Hi there Mevi, I'm thinking of swapping my regular 180 hinges to 270 just so I can keep the back door open even when it's windy. Why did you decide against those 270 hinges? Thanks

@Mevi

4 жыл бұрын

Word is that the 270 hinges get more and more stiff until they fail or start to deform the door around where they bolt on. My own experience supported that. They were already stiff and oil just can't seem to penetrate the 270 hinge to prevent them seizing up.

@Szymon8739

4 жыл бұрын

@@Mevi thanks! You just saved me 200euro 👍

@Mevi

4 жыл бұрын

@@Szymon8739 never a problem. An option you have for keeping *both* doors open is a pole to extend between the tops of the doors. They are often included with rear door awnings, but you would be able to make one yourself.

@Mevi

4 жыл бұрын

@@Szymon8739 like this: www.leisureoutlet.com/awnings/camper-van-awnings/rear-door-awnings/7199-fiamma-ducato-rear-door-cover-awning

@Szymon8739

4 жыл бұрын

@@Mevi that's actually genius. I'll make something like that myself. It'll double up as a pole for outdoor shower curtain

Those doors sound expensive when you shut them now.....doesn't demo the expensive sounding doors closing...... :) I thought that was well worth doing for the money Mevi!

@Mevi

5 жыл бұрын

I think it was pretty late when I finished up that night. I'm sure I slam the back doors in a later video, but imagine CLANGGG vs THUNK. Yeah, just like that. 😁

Why change the doors being able to change only the hinges?

@Mevi

Жыл бұрын

The original doors were accident damaged

@angel3067

Жыл бұрын

@@Mevi The originals were 270?