Thank you for watching. Please check out the description for any tool recommendations.

@Gekite

9 күн бұрын

wasn't able to watch as something wrong with KZread ads not playing and preventing the playing of the actual video! Well done KZread, cripple your own site!

Mark - it’s been brilliant watching your journey from a “give a go” guy to now doing very smooth (and that’s not just your head..) videos - you’re an inspiration as I’m a few months (maybe years at my speed) behind you. Keep at it - I’ve learnt a lot from you and well done staying humble. Just proves you don’t need to be either Canadian or have decades of daily woodworking to be a quality craftsman (craftsperson?). But 2 hours in and nearly 500 views - on a Saturday morning - shouldn’t we all be out woodworking not watching KZread!

@startmaking1

Ай бұрын

hi Matthew. It's very odd looking back and still missing the old shed. And the early videos and their hurdles in filming and lighting etc. I appreciate the kind words bud. They mean a huge amount. Especially the humble bit. It is my number one aim to just be myself and not get carried away in the whole journey thing. not that I am even close to being a big channel. But your best point is well made. We should be all out there making where possible. Me included. Take care bud.

One thing to keep in mind with the remote receptacles. Advice from a master electrician, most of these type devices are only rated at about 12-15 amps. Larger tools say a compressor, sliding compound miter saw, table saw, or even things with heating elements(ie coffee pot) usually pull 15+ amps. It is a bit like the power strips, many house fires in the states during the winter as people plug in space heaters. It is the number one cause of house fires here. Also the workshop companion is a wonderful knowledgeable channel/fella. He has written several books. He has an ingenious panel moving system.

@startmaking1

7 күн бұрын

That is great detailed advice. Thank you. And a good recommendation for workshop companion. Thank you.

@TNBushcrafter

7 күн бұрын

@@startmaking1 quite welcome. Thanks for the great content!

There I was earlier today trying to work out a way to carry a 8x4 osb board and here I am now whipping together a panel carrier from an old chopping board that handily already has a handle slot (just don't tell the wife) 😅👍

@startmaking1

Ай бұрын

Chopping board is a god idea. So long as the handle doesn't give at all. If it is strong it may just be the best use of a chopping board yet , Nice.

I glued ½” thick carpet foam (looks like the OSB of the foam world) for the grip surface of a push paddle like yours. My pushers are about 10 years old and could use a rebuild but no complaints, they’re still pretty grippy and stood up to an occasional slice by the blade.

@startmaking1

29 күн бұрын

I know the stuff you mean. What a great idea. Thank you.

A couple wedges + a couple rails + something to smack the wedge can also help you clamp work. 👍

@startmaking1

19 күн бұрын

I love this idea. Have seen is a few times and love the simplicity,.

I want to give you an extra thumbs up for adding US links for all the tools!👍

@startmaking1

Ай бұрын

Lol, Thank you very much bud. Appreciated,.

Your Videos are within the best out there. Always profound, reflected and explained well; with good humour. thx for sharing your pragmatic and mature way of doing things

@startmaking1

14 күн бұрын

Wow, thank you. there are lovely comments and then there are comments that spur me on to make more videos with a big smile on my face. This is one of those and for that I am grateful.

Kia Ora Mark. Your a bad man just made me look at buying more tools 😂 I’ve already spent $14k on my little workshop tools and vac system now you just show me more tools.. Awesome keep up the videos mate..

@startmaking1

Ай бұрын

Kia Ora Bud. Apologies lol. I bet you have some cool toys for that though. Probably best to not tell me as I will be very jealous. Take care.

Love your ingenuity. 🙂👍

@startmaking1

20 күн бұрын

Thank you. Much appreciated.

Very grippy...love it!😀

@startmaking1

18 күн бұрын

lol brilliant. Thank you.

Another top quality video, great advice, thanks mate! 👍🏻

@startmaking1

Ай бұрын

Thank you much appreciated.

The matchfit clamps work well in my dog holes. But you are limited to the spacing of those holes As far as the matchfit push sticks, they are amazing. You do have to clean them frequently or the sawdust just makes them slick like the rubber. Also it stings a little when you run the green piece accidentally through the table saw blade. Have done it a few times BUT it still functions perfect!

@startmaking1

7 күн бұрын

I have just drilled a complete set of holes and still think I need dovetail grooves between them. I really like the push sticks and have made some of my own to compare. More than were shown in this video. I cant imagine how annoyed I would be if the gripper goes through the blade, not cheap.

Good tips, thanks!

@startmaking1

Ай бұрын

Thank you Robert

Great tips, as always.

@startmaking1

29 күн бұрын

Thank you Mark

lol i totally thought the router table was wayyy bigger and sitting in the corner until you put your hand on it and i realised its a benchtop table :) . The whole time i was thinking, thats a smart idea to put the router plate into a big table and make a tall fence with a 4 inch dust port in the fence and all of a sudden i was like whatttt.

@startmaking1

29 күн бұрын

Love this comment and now I want a giant router table. Or just a giant table with the router in it.

I bought one of those panel carriers - not a Kreg, but resonable quality - specifically to move some 8x4 sheets of 18mm MDF. Fail. The face of MDF is v. slippery, and the 18mm sheets are f*$^ing heavy. The carrier did not grip with sufficient force to lift them. It would probably work on ply, or possibly thinner MDF, but for a full sheet of 18mm go for the 'under' carrier - physics will be on your side.

@zapa1pnt

Ай бұрын

Years ago, I learned the hard way (moving multitudes of folding tables) MDF weighs 3 times what plywood does. That's how you learn, to move the MDF First. 😁✌🖖

@startmaking1

Ай бұрын

And ply is heavy enough #zapa1pnt Nearly finished me off carrying a few sheets of 18mm the other day.

@startmaking1

Ай бұрын

That is a really good point. In filming I was getting a lot of slip too. 18mm of any sheet is pretty heavy.

You could try an old ping pong bat for the surface of your pish block. Just peel off the rubber and *ahem recycle it for your pish block

@startmaking1

20 күн бұрын

Thank you. Much appreciated. What a great idea.

Spot on mate.

@startmaking1

20 күн бұрын

Thank you. Much appreciated.

I haven’t got a scraper yet but my birthday is coming and I will be presenting my kids with a comprehensive list. ;) Great video, Mark. You should release a shorter one on your push pad thingy. I know it’s simple but there’s still a benefit seeing it done.

@1pcfred

Ай бұрын

If you really want to splash out get an accu-burr. Supposedly they make turning the burr easy.

@startmaking1

Ай бұрын

Already in the making Roger. I had it all in this one but it was way too long. So I plan to do a make your own tools video. Wont be too long. Cheers.

@1pcfred

Ай бұрын

@@startmaking1 making your own tools can be very satisfying. Modifying tools to make them more useful or desirable is fun too. Customized upgrades.

Another great video. I always love a homemade solution over just shilling for companies. Having said that... If I took the time to tell you how addicted I am to Microjig I wouldn't have time to buy more stuff from them. A possible fix for your push paddle, microjig used to sell the rubber pads with self adhesive backing in the replacement parts on the website. It has been a while since I needed one, so I am unsure if this is still the case.

@startmaking1

Ай бұрын

Hi Corey. Hope you are doing well. I am planning a video with the build of this, although it is relatively simple . And am compiling some more to add to it. Life is really expensive and we have loads of scraps, especially ply. Oh and Micro Jig , although I am kind of pushing the clamps while saying make your own paddle, are still about to get a fair amount of my trade in the coming months. Im hooked. Great shout on the replacement pads. I will take a look. Thank you.

Great advice mate 👍👊

@startmaking1

29 күн бұрын

Thank you very much.

dude- thx- i always learn something with your vids

@startmaking1

20 күн бұрын

Thank you. Much appreciated.

Another great video Mark 👍🏽

@startmaking1

Ай бұрын

Thank you very much

Thanks so much. Those were some really handy, practical tips. I really appreciated the "but you can also make your own" alternatives.

@startmaking1

Ай бұрын

Hi Andrew. I appreciate it . And I quite fancy doing a video on making your own as life gets more and more expensive.

Another great video. You've recommended some great tools, not just in this video. I appreciate the honest reviews

@startmaking1

Ай бұрын

Thank you very much. I appreciate it a lot.

Great job and products thx for sharing enjoyed it Keep building Cheers

@startmaking1

20 күн бұрын

Thank you. Much appreciated.

Good tips, and pleased to see homemade options alongside commercial products. I absolutely love speedsquares, amazingly useful and intuitive; one of my very top recommendations for anyone putting together a toolkit.

@startmaking1

Ай бұрын

100% agree. I love making tools. I want to do a full video on it as it is a great way of saving money and you get something far more tactile.

'Just buy aluminium ones.' Why buy? We are makers, aren't we? Could not be simpler- buy a length and cut up. Lots of other clamps can be made too. Dovetail slot along the apron- you can clamp to an apron anyway- that is what it is for... G clamps are way stronger, and can be picked up in flea markets. They have been making them for centuries. For good reason. You should NOT, repeat NOT use bridging push blocks on a table saw- because you need to remove the blade guard- which you should NOT do. Circular saw- save the money and put to a tracksaw. Way more useful. Speed squares - you can also get speed T squares. Auto-detect power modules are around £30- well worth it. Tape dispenser- make it! For several tapes, while you are at it. Great info on card scrapers!

@startmaking1

Ай бұрын

Ah , I've missed your input lol. Thank you.

@Tensquaremetreworkshop

Ай бұрын

@@startmaking1 Sorry, I will try to be more attentive… 😎

@startmaking1

Ай бұрын

@Tensquaremetreworkshop I didn't really understand what you meant in the first line. A length of what. Happy to learn here. Ps I am planning on making quite a few tools but sometimes these videos being aimed at beginners need to recommend tools etc that don't need to be made. Not all beginners start with the skills and tools to make everything.

@Tensquaremetreworkshop

Ай бұрын

@@startmaking1 Metal suppliers offer aluminium bar in a range of sizes. You can get 3/4” (US) or 20mm (rest of world) for dog holes. Cut to length you desire (hacksaw). A fraction of the cost of commercial dogs. Steel (tube will do) also available- or brass if you want to be fancy. I have a couple of videos on making clamps for dog hole arrays.

@startmaking1

Ай бұрын

@@Tensquaremetreworkshop ah I see. Sounds very sensible. Thank you

Hi Mark, Great advice with those bench dogs and clamping we all need to fasten our work down on the bench. Good tool and a must have a card scraper I've go two standard ones they were given to me about ten years ago. I have a Record No5 and a Stanley No6 wood planes and I use a candle to wax some times i'll use silicone spray. As always good advice and your honest opinion that counts, Great video Take care

@startmaking1

Ай бұрын

Hey Shaun. I have not tried silicone spray. Great advice. Thank you bud.

I made a panel carrier form one of your earlier videos. Complete game changer!!

@startmaking1

29 күн бұрын

Hi Chris. I am glad that it has helped. Thank you.

Great video Mark so many great tool tips if gotten from you Sir Thank you so much for such great videos. Keep up the great job and I hope you and your family have a great holiday weekend.🎉🍻

@startmaking1

Ай бұрын

Hi Jim. Many thanks. Had a lovely weekend. I hope yours was enjoyable too.

I am going to have to try the dovetail clamps. I like the idea of using a separate board for the grooves. These are great tips, thanks.

@startmaking1

Ай бұрын

It has worked well so far. I would recommend closer grooves than mine and maybe dog holes between each square made by the grooves. Thats my plan.

One thing to note with your sheet goods carrying jig is that depending on the shape/size of the sheet, it might be hard to keep balanced because the centre of gravity is above the ‘pivot’ point (where the wood rests on the jig). With the one from Kreg, the centre of gravity hangs below the pivot point, so as long as it’s being picked up from the middle it’ll keep itself balanced automatically. i do agree that your jig would be a more comfortable way to carry though! And I’m now on the hunt for where to buy a card scraper…

@bdmayhem3391

Ай бұрын

The trying I like about the kreg panel carrier is that I don't need to lift the plywood before I can use it. I mean, I wanted a carrier in the first place because sheet goods are hard to lift.

@startmaking1

Ай бұрын

Very true about the panel carrier. And I do understand that not everyone wants a scraper. I guess all I am trying to say is that people dont need to get good enough to use one. Which is a common misconception. More about using one and learning as you go.

@georgeyoung2684

Ай бұрын

@@startmaking1 Oh dang I typod, I meant I am NOW on the hunt for a card scraper!! It just arrived today in fact, excited to give it a try on my next project!

As a full on cheapskate, I have a versatile solution to the clamping dilemma. I have a grid of holes drilled through the worktop with M8 pronged t nuts on the underside. I have a selection of bolts and threaded bar which give me lots of clamping options. If I find there isn’t a hole where I need one I just put one in. For even more versatility- the worktop has a sheet of perforated hardboard on the top. That has a grid of perfectly square holes in it which take 6mm dowels.

@startmaking1

19 күн бұрын

that is a super idea. Really smart.

My dust extraction is a power takeoff from the hoover. Plug in the tool, turn it on and the hoover starts. As I don't have a bunch of tools to run, it works for me. Thanks for the post. Take care & stay safe.

@1pcfred

Ай бұрын

My dust extraction is a bench brush. Just sweep it onto the floor and shovel it up.

@startmaking1

Ай бұрын

Thats sounds nicely simple Doug. I may opt for that if I get another extractor/hoover. The one I have is way too loud long term.

@dougdavidson175

Ай бұрын

@@startmaking1 A £20 cyclone and 2 buckets mated top to top. A pool filter sock over the hoover filter to help with the fine dust. The hoover needs dumped regularly but provides a good source of glue filler stock. A cart from pallet wood and salvaged wheels makes it easy to move from storage shed to 'workshop'. Uprights and crossers at each end make a good handle and provide storage for attachments, hoses and cords.

@startmaking1

14 күн бұрын

Wow, that is a great use of a few buckets and a filter sock. Very nice work Doug.

I'm sure there are Moor tips from you Mark belting as usual keep going mark love your vids rkid 👍👍👍

@startmaking1

Ай бұрын

Thanks Ant. Appreciate it as always.

Nice one! I’ve just got a couple of the Microjig dovetail clamps… great idea. As well as your chunky bench top board, they’re great in something like a piece of 18mm ply for making a jig that you can run through your table saw, to straighten up boards that don’t have a straight edge 👍 You’re right… there’s a whole rabbit hole full of expensive dovetail accessories…. I’ve just started experimenting with 3d printing some little dovetail sliding blocks which could be handy for mitre stops etc.

@startmaking1

Ай бұрын

You are spot on. And that jig is on my list for next week. I like the idea of 3d printing the hole down parts. Really smart.

You’re totally right about scrapers, massively underrated piece of kit! Nice video mark. 😊

@startmaking1

Ай бұрын

Thank you Alex. Do you have a couple of scrapers. I had an idea

@michaelwillson6847

Ай бұрын

@@startmaking1 sounds interesting this colabriation on the cards. 🏴󠁧󠁢󠁳󠁣󠁴󠁿👍🤔

@startmaking1

14 күн бұрын

Now that would be fun Michael.

@michaelwillson6847

14 күн бұрын

@@startmaking1 make it happen you 2 think would be awesome 👍🏴󠁧󠁢󠁳󠁣󠁴󠁿

I’m totally enjoying the video already! Quick note- the simple paddle push blocks can have 80 grit sandpaper glued to the bottom (spray adhesive) and that will give them good grip. You could do the same thing with the DIY block over the cork or instead of.

@zapa1pnt

Ай бұрын

That will depend on what you are working with and if the grit scars may be a problem. 😁✌🖖

@startmaking1

Ай бұрын

Sand paper is a great idea. Good so long as you are yet to sand the item you are pushing which most times you are. Thank you. I tried silicone but no glue I had could stick it. I should have known as it is what they use for glue brushes and such.

i have a similar set up with the dust extraction. its a game changer😊

@startmaking1

Ай бұрын

Simple but so effective.

If you want to go even cheaper on bench dog clamps just a couple wedge of wood pushed in with a mallet against a regular bench dog will work just as well. Similar idea to the ujk peanut system

@startmaking1

Ай бұрын

Oh I like that idea. Mainly due to the simplicity and cost, thank you

@wonkypegworkshop

Ай бұрын

@@startmaking1 and if you can drill dog holes through grab a simple holdfast. Cheap simple and very effective

great tips i need to make a panel carrier , how about adding a padded hooked bungie to hold the panel from tipping out on you (when you open the door or such)??? great vid enjoy you always have fun from Oklahoma

@startmaking1

Ай бұрын

Thats is a really great idea. especially on a windy day when the lighter 1/4 inch panels love to become sails.

This video has lots of good information Mark. I have seen the dovetail clamps & the various dog hole accessories before & both interest me. I've even seen a couple US woodworkers build a small stand-alone workbench for the dovetail clamps. I like your use of the thick slab clamped to your benchtop even better. You just put it away when done & it's out of the way. With a Frech cleat at one end, it goes on your shop wall. Your wooden push block looks useful. If the adjustable end stop gets chewed up, just make a new one or flip that one upside down. There are rolls of rubber sheeting mats marketed for kitchen use that often woodworkers set beneath their sharpening stones to keep them stationary. It grips well, but I don't know how well it would glue. You might have to clamp or staple it to wood. But I would think your type of glue would be important too. I've owned a Swanson speed-square or years. Yes, it does come in handy. I've thought about purchasing or making a bigger one. One last comment about scrapers. I have that 3-piece set you show, but have never sharpened the gooseneck one. I know it's harder to do than the straight one. Do your thumbs ever get hot or burned from pushing a scraper blade? Mine have. I cut a magnetic sheet to fit the back of mine & keep the heat off my hands. See you in the next video.

@startmaking1

Ай бұрын

Hi Bill. I have also seen these work benches and am severely tempted. I have to make some cabinets and the top will have to be a bench of some sort. I even saw someone have a slab like mine but then it was made into a right angle so it has a side aswell. Not sure where I would store it but it looked really useful. Not as heavy as mine as only ply, probably 2 sheets of 3/4 inch. Funny you mention the grip cloth. I have some for sanding and it is ok. Does lose some stick with sawdust though. I am planning a build your own tools video and will make a few paddles. I could not get silicone to stick but will try the rubber matt. Worked well on my clamp handles. My thumbs definitely burn on the flat one. Great idea on the magnetic strip. I was pondering about cork but not sure, would probably flake. The goose neck one is great for curves. One that you hardly ever use but when you do, it is priceless. Sharpening it is a pain but doable. The wood whisper shows it best. Im yet to perfect it. take care. And thank you as always for sharing.

Love the channel, especially the workshop build. 👍 Only issue I have is that the remote switches are ok and was looking at using them myself. However quite a few You Tube vids highlighting a big problem, certainly with cheap Chinese manufactured ones. Sometimes other devices in the home for example can interfere with them and turn them on accidentally . Meaning if the main switch is left on the vac for example, this potentially could turn on by accident. Obviously this is only a problem if no one is in the workshop at that time. This can lead to the vac potentially burning out if on four hours and potential fire risk? Or if using a separate cyclone and bin. This could actually implode on itself if using dust gates and they are closed. I don’t think this would happen in your workshop as I guess it’s well away from the main house and any potential items that could interfere. Also to get over this just make sure when finished for the day that the main switch is turned off, but people can forget. I think it was on either 10 minute workshop, Charlie-Diyte or Rag & Bone brown. Can’t remember🤷🏻. But as long as you’re careful and understand the risk then shouldn’t be a huge issue. But just wanted to make you aware and not the H&S police here 🤣.

@startmaking1

Ай бұрын

Thank you Mark. It was Keith Brown. I think his were matched to a car key sensor and his extraction ran through the night. I still turn my entire electrics off when I leave the workshop which I should have pointed out and will correct in a video at the end of year where I point out my mistakes through the year. Really good point bud.

@markgeezey1809

Ай бұрын

⁠no problems. Hate being one of these people that harp on about health and safety. But in this instance thought it wise so nothing can come back on you. 👍 keep up the great work.

@startmaking1

14 күн бұрын

I appreciate the feedback always. Thank you.

Great video. Maybe more in the future of using your head to test the grip of items? 😂

@startmaking1

Ай бұрын

I could do a whole series on this. Not like the head is getting any less bald lol.

@chriscollins9717

Ай бұрын

@@startmaking1 I was thinking maybe a whole series could be done out of this. What can I treat sharpness with on my arm? What can I hammer using my leg? What can I measure using my, er maybe not the best idea for a family friendly series 😃

Cracking video as always m8. Must say I have similar push pads I got with my thicknesser and they have a rubber on the bottom I really like them. But my opinion instead the rubber cork use the rubber matting stuff you can buy on a roll for like 3 quid from BM or places like that. Certianly few things to consider there 👍🏴󠁧󠁢󠁳󠁣󠁴󠁿

@startmaking1

Ай бұрын

Hey bud. Funny you mention the rubber matting. I am planning a build video of this and a few others and this was one of the base options. Nice one bud.

@michaelwillson6847

Ай бұрын

@@startmaking1 that rubber Matting works really well also for sanding when I eventually get new saw and bench built an thinking of incorporating a section on it for few different things. Although had development will catch up with you email 🏴󠁧󠁢󠁳󠁣󠁴󠁿👍

Scrub most any rubber surface on the push blocks with isopropyl alcohol and it will clean the fine sawdust and renew the surface. Good grip .

@startmaking1

29 күн бұрын

I will give that a shot. Thank you. I hate throwing anything away.

Yeah. I would def connect the dovetail channels with the dog holes. If you don’t know, try to both, depending your later income. I love my micro channels personally, but haven’t used dogs yet. It’s a future thing for me to try out for me. There’s one way to do anything in ww or life. You do you overall. I so support this channel overall.

@startmaking1

Ай бұрын

Thank you Arron. I very much appreciate it.

Thanks for sharing. Would you do a video on the right way to use various tools? That would be very helpful for me.

@startmaking1

Ай бұрын

Hi. Would have to feel confident that I was giving good info. So I guess it would depend on the tools. But in theory I love the idea.

@feestuart2499

Ай бұрын

@@startmaking1 I break drill bits what am I doing wrong? Also my screw heads strip easily how can I prevent this?

@startmaking1

14 күн бұрын

Gosh. I am certainly not an expert on this and there can be a huge amount of factors. For me the screw heads stripping is a combination of either too much power (usually an impact driver thing), or if you are using a drill , then either the wrong sized bit. Some screws have larger and some have smaller heads and hence different sized bit needs. Or your bit may be worn from past slips. this is one I often overlook as I dont want to buy a new one but of the edges of a Philips head bit for instance are worn it will get less purchase on the screw. Or if you are screwing into a very hard wood the screw could be struggling, then you need to predrill the hole with a bit that is around the same diameter as the screw minus the thread. I would suggest the bit size is the most common reason for slip though. Breaking drill bits I assume is small ones as larger / thicker should not break easily. The smaller ones are always breaking on me. My issue is dropping my drill with the bit in it. But the other reason is cheap bits and when they get hot the have too many weaknesses from being badly made and snap. I hope some of this is useful.

Mark, another great video share. Love some of your upgrades/improvements. I still think Gravity is one of the best work holding concepts especially when combined with jigs as this improves technique faster than using clamps but I accept this is harder for beginners to manage and you do need to make the jigs etc. You demonstrated this well whilst showing the scraper against the bench dog, freehand holding at its best. Nice one!

@startmaking1

Ай бұрын

Thank you Ian. you are right about Gravity. I do like the idea of heading down a jig making route. I definitely need a fair few of them. Would you believe that I am actually slightly regretting the laminate on the bench as it is so slippy. At least ply had some friction for holding against. Nothing is perfect I guess.

@ianpearse4480

Ай бұрын

@@startmaking1 Hi Mark, As you have lots of dog holes you could think about making thin strip stops as fences with dog holes and/or fitted dowels in the dog holes, I use 6mm strip wood with that rubber drawer matting thingy on the bottom. I even planned a few down to 3mm.

T slots are fine in wood so long as you go deeper.

@startmaking1

20 күн бұрын

Great advice.

For the foam pushers could you use ca glue to fix sand paper for a better grip?

@startmaking1

29 күн бұрын

Great idea.

Hey Mark! Where are all of the off cuts from your rubber roof.?? Very grippy.!!!!

@startmaking1

Ай бұрын

I was so quick to act and threw them away. Gutted. They would have come in handy for so many things. I am tempted to contact the company as they have had a ton of free advertising from me. See if they have any off cuts. Would make a brilliant sanding grip and also probably good for sanding tools. I could glue velcro to it. Now I am kicking myself. You did say at the time but I was publishing videos a week behind. Gutted.

Hey Mark, really like your small Microjig table you made. Here is something to consider: Since it is so thick, why not cut dovetail grooves on the bottom side in the center of the grooves that are on top? This way you can use a couple of Microjig clamps to attach it to your table without sacrificing any strength of the slab itself.

@startmaking1

29 күн бұрын

Now that is a great idea. The bottom was going to be my spoil board or sorts, something to put under a piece when you drill it but as |I am yet to use it for that I think I will try your idea. thank you.

@gregghernandez2714

28 күн бұрын

No problem. I am all in on the Microjig system. So effective for all kinds of uses. Love your channel.

The remote would be useless if the extractor used a nvr switch which unfortunately covers most workshop dust extractors that use 4 inch hoses built in the last few years

@startmaking1

29 күн бұрын

Fair enough. Mine is older than that. I guess it is still good advice for people who don't have newer systems. Plus I guess you could use them for other things. I have my lights on them still so I don't have to reach up to each light individually.

@AndyCarnegie

29 күн бұрын

@@startmaking1@startmaking1 Yeah, NVR switches are a pain.I understand them on machines with dangerous spinning parts but I think a dust extractor is pretty safe after a power outage. There are several solutions for machines with NVR switches, but they are normally £100+

@startmaking1

14 күн бұрын

That is a good point. I dont have enough machines to have much experience But I would also expect them to be only on the spinning finger taking machines.

what was the small cordless drill that you toss at the beginning of the video? Not sure if I've seen you use (or say why it's bad) before

@startmaking1

19 күн бұрын

I had to think where I got it. Ages ago it did a fun supermarket tools video and bought this Parkside electric screwdriver. In truth it is ok for what it does but not really for woodworking. More household jobs. Doesnt really have the strength but that is not a surprise.

Again, nice work with a brilliant presentation. Are you Simonizing (American car wax product from the 1950s) that laser? You might as well, it probably costs as much, or more than, my first vehicle did. Have any of us really figured out how much clamping pressure is needed for each operation? My thinking is that we all think we need a lot more clamping pressure that is really required for each type of glue up. Sometimes, more is not better. I know the most pressure I've needed to use is while straightening out some spruce for my daughter's kitchen island top; otherwise, cabinets and boxes not so much. And, please, don't ever use TikTok. The best sheet good carrier I have tried is my son. I've not dropped a piece, or strained myself, since I've started making him do it.

@zapa1pnt

Ай бұрын

Back in 1971, I purchased a '64 Impala for $75 I drove it for several years (until it was trash) and sold it for $75. 🤣👍 😁✌🖖

@startmaking1

Ай бұрын

Thank you Meat. I need a panel carrier like yours. I wonder which of my 2 daughters will be the strongest. May have to wait a few years yet. It's funny that a guy like me decided to show him taking care of the laser. In truth I treat it pretty badly. ITs the whole reason I didnt peal the protective film off the top. And I still out the polystyrene packing on top so I can use it as a table top for junk. lol. And dont worry I neither understand tik Tok to know how to do it. Thankfully. Instagram was enough of an eye opener. You are spot on about clap pressure too. Suman woodcraft did a good video on it testing pressures. Very analytical but interesting. Still a mistake I make regularly. Take care bud.

@themeat5053

Ай бұрын

@@zapa1pnt Those Impalas were the best. It was my father's car of choice until 1976. The '64 drop top my cousin drove was the bomb!

@themeat5053

Ай бұрын

@@startmaking1 Thanks. I'll need to review that Suman woodcraft video. I used to clamp stuff so tightly that I would knock it out of square. Then there was a real nightmare. Re: which daughter, I know that all three of mine are stronger than my boy (but he's pretty capable). Those girls will surprise you with their acuity, strength and resilience. My boy is the youngest and I realized that anyone can raise a son. It takes a real man to raise daughters (there's that darn degree in Philosophy again). Cheers! Have a good week

@startmaking1

14 күн бұрын

MEat. I am already relating to this from the daughter stand point. They are so smart. Way smarter than me and so much more aware. I was just a kids swinging sticks in the garden at their age, they are sensitive and kind but also strong and hard willed. Passionate and honest. 4 kids huh? I bet that is a fun house when they are all at home. Have a good week bud.

Can you use anything other than the matchfit bit? I only have 1/4 inch router.

@startmaking1

29 күн бұрын

I don't have the official bit. I did one run with a straight bit, then followed with a dovetail bit . Takes a bit of test cutting to get it lined up.

What was the isolation switch you were using...???

@startmaking1

19 күн бұрын

I was just using cheap remote plugs. There is a link in the description.

Hi Mark. I’ve been wanting to use those remote sockets for my dust extractor for a long time now but the motor on my has a NVR switch on it and can’t figure a way of bypassing it without the help of an expensive electrician. Have you any experience on this for a novice to do. Or could you possibly do a video on this issue. Thanks in advance.

@startmaking1

29 күн бұрын

Ah, I didnt think about that. Good point. I have seen a couple of videos about how to bypass but am very wary as to whether I would want to. I am sadly not qualified or experienced in this area. Maybe in time.

Hi

@startmaking1

Ай бұрын

Hi.

With the panel carry, i feel like you should not be making statements like that ("its better on the body to do this, instead of this") unless you actually have some scientific knowledge to back it up, not just because you feel better doing it that way. Because i get the feeling that having it pull directly on the shoulder joint instead of spreading it across the 3 joints in the arm is not good on the body, but it would take a doctor who specializes in the joints of the body to be able to clarify which is right. Now, i do realize i kinda just did the same thing, but im just some guy in the comments, not the person presenting facts in a video to thousands of people who watch it. Also, with that jig, you have to lift the panel first to slide it underneath, so you would probably need the Kregg one to lift it first then slide the homemade one under the panel before you can carry it away. Where the Kregg product lets you just lift and go.

@startmaking1

Ай бұрын

Hi Paul. I followed the review directly with the line, I am no expert in anatomy but that feels like it should be better. I think that this is enough to show people that I am not considering myself to be an expert dishing out facts. though I do get your point. I also hear what you are saying about having to lift the panel but you dont need to in its entirety. You can just lift one end and the carrier pops underneath. But go in what ever direction you feel is best, I am just a guy talking about his experiences. I appreciate the feed back thank you.

@paulmccullough7352

29 күн бұрын

@@startmaking1 Thanks for your response. I guess my main point, that i didnt really articulate properly or maybe at all was, when it comes to the way we move and use our bodies, just because it feels like it is the best or easiest way, doesnt mean that it is, and can cause unnecessary problems later down the line.

@startmaking1

29 күн бұрын

| 100% agree. And you are right. I do need to be careful about not giving advice in areas that I dont have experience / expertise in. My line that I am not an anatomy expert is vague but I did cut a chunk out about taking advice from someone qualified. I get annoyed when editing these videos as I cut out hours of talk that actually is quite relevant but people just wont watch something that long. I appreciate the heads up. It is good to have these things in mind when I film the next video. Thank you.

I love your videos but the colour balance at the beginning is... err.. well. Terrible. It's terrible. Overwhelmingly pink. It's even a bit distracting.

@startmaking1

Ай бұрын

Thank you. Im not sure what it is as it is nothing more than a tint on my laptop I use for my editing. I will take another look. I was finding the grey and white a little cold and stark and wanted to warm it up. But not if it is annoying. Appreciate the heads up.

@peterjohneggleton2011

Ай бұрын

I thought you just liked pink…… sweetness.😂😂

@fgjhham89

17 күн бұрын

I like it! Makes the shot more interesting. Maybe you could try placing the lights a bit further away so that it's more subtle?

@startmaking1

14 күн бұрын

You got me. I really do.

@jonbloodworth474

6 күн бұрын

As another bald content maker, it just seems to bright to me, I often have to turn down the brightness because I don't have hair too darker up the pixel average. The contrast also seems high. I'm not great at editing picture but I do find adjusting brightness helps loads. The backlight being magenta purple pinkand behind you doesn't help either, it s very well lit but the color light seems to conflict. Hope this helps! Also, bench dogs and 2 wedges that make a rectangle when together works extremely well for hold downs and can be made very slim so you can use a hand plane, sand, whatever that needs an un obstructed top surface. Cheers!