Just Burnie the box in an insulated ammo box or 2 gallon bucket under the ground about a ft! I live in the UP of Michigan an get 2’ of snow an zero temps! These batteries last 3-4 weeks taking 50-75 pics a day,
@joneshuntingadventures79712 жыл бұрын
Thanks for another good video.
@michaelo6003 Жыл бұрын
Great vid, Mike, thanks! I use the PS-12120 batteries. I'd like to install a small solar panel to keep them charged in the field. Am I correct that a panel in the 2-5 watt range will be adequate? Thanks! Michael
@jessetolliver5347 Жыл бұрын
any clue when your going to get more boxes in?
@herd360
Жыл бұрын
They have been ordered. Not sure if production has started or not and then shipping so I don't expect to see them before October
@jessetolliver5347
Жыл бұрын
@@herd360 thank you for letting me know I will check back then
@jerryellingson7349 Жыл бұрын
using a lifepo4 battery with bms ,to be even further protected against high voltage damage to my browning camera, what size inline fuse would i use? what voltage would damage my camera thanks much for your help
@herd360
Жыл бұрын
An inline fuse only protects from the fuse backwards to the battery incase the cable shorts out somewhere between that point and the battery. For the last 10plus years I've never used a fuse with a trailcam on external power except my 1800 boxes where there is one inside the box. I have a 2amp fuse on those. I use these batteries on my cams. Their 13+volts is perfectly safe.
@jerryellingson7349
Жыл бұрын
apparently you feel the possibility of the battery freaking out and overloading the camera is very low, correct? thanks for your help again!!
@herd360
Жыл бұрын
@@jerryellingson7349 I certainly would never say it's not possible because it would prove me wrong. However what do you mean by overload? More voltage? That would not blow a fuse no protection from over voltage. Over current? The only thing that would blow the fuse is more current being pulled through the fuse than the rating. Since current is not forced from the battery but pulled from the battery by the device this again doesn't offer protection from the battery. Also I read over what I typed earlier and worded it incorrectly. If there was a short in the wire after the fuse then the fuse would blow. This would prevent the wire from melting from the short back to the battery.
Пікірлер: 10
Just Burnie the box in an insulated ammo box or 2 gallon bucket under the ground about a ft! I live in the UP of Michigan an get 2’ of snow an zero temps! These batteries last 3-4 weeks taking 50-75 pics a day,
Thanks for another good video.
Great vid, Mike, thanks! I use the PS-12120 batteries. I'd like to install a small solar panel to keep them charged in the field. Am I correct that a panel in the 2-5 watt range will be adequate? Thanks! Michael
any clue when your going to get more boxes in?
@herd360
Жыл бұрын
They have been ordered. Not sure if production has started or not and then shipping so I don't expect to see them before October
@jessetolliver5347
Жыл бұрын
@@herd360 thank you for letting me know I will check back then
using a lifepo4 battery with bms ,to be even further protected against high voltage damage to my browning camera, what size inline fuse would i use? what voltage would damage my camera thanks much for your help
@herd360
Жыл бұрын
An inline fuse only protects from the fuse backwards to the battery incase the cable shorts out somewhere between that point and the battery. For the last 10plus years I've never used a fuse with a trailcam on external power except my 1800 boxes where there is one inside the box. I have a 2amp fuse on those. I use these batteries on my cams. Their 13+volts is perfectly safe.
@jerryellingson7349
Жыл бұрын
apparently you feel the possibility of the battery freaking out and overloading the camera is very low, correct? thanks for your help again!!
@herd360
Жыл бұрын
@@jerryellingson7349 I certainly would never say it's not possible because it would prove me wrong. However what do you mean by overload? More voltage? That would not blow a fuse no protection from over voltage. Over current? The only thing that would blow the fuse is more current being pulled through the fuse than the rating. Since current is not forced from the battery but pulled from the battery by the device this again doesn't offer protection from the battery. Also I read over what I typed earlier and worded it incorrectly. If there was a short in the wire after the fuse then the fuse would blow. This would prevent the wire from melting from the short back to the battery.