Amazon Store, Facebook Page, And Email Below Outdoors With The Morgans Amazon Page www.amazon.com/shop/influencer-0dd9f808 Link to our Facebook Page facebook.com/Outdoors-With-The-Morgans-1326440487390931/ outdoorswiththemorgans@gmail.com

@OutdoorsWithTheMorgans

6 жыл бұрын

Wesley W, there is no marks because what you see is the marks. Like two grade stakes, one in front of you and one to the left, once you line them up (looking through prism) you have a 90. Make sense?

@mitchdenner9743

4 жыл бұрын

@@OutdoorsWithTheMorgans so if you wanted to run a perpendicular line 90 degrees off of that woodpile if you sight down the left side of the woodpile like you did and you had somebody with a stake by your truck move it until it lined up from middle screen to bottom screen with the left side of the pile is that correct?

I've had one of those since 1968 when I started working as a surveyor. The notch in the bottom is for a plumb bob to get your 90 degrees off an exact point.

@WILSON.1

6 жыл бұрын

Wow, that's awesome. I was wondering how you would get an exact point.

@Twooldfartsnavigaitingyoutube

4 жыл бұрын

QuantityEngineers Exactly!

Yes, I bought one 35 years ago when I built my first house and used it to layout the footers! Now I'm laying strings out for a garage footer. Took me a couple hours to find it... Works great! Oh, and be sure to use a plumb bob to get accurate readings.

Used one of these for years doing survey work. Came in very handy doing cross-sections.

I had one when I was 15. Now 73, remembered it, looked on Ebay, and confirmed it still exists. Searched KZread for proper uses, and here we are. It was a great tool then, and now! Thanks.

My dad had one a long time ago. I had forgotten about it until this video. It is a very handy tool to have.

I remember playing with a prism in grade school but this is the first time I've seen one like this and understood the use. You mentioned that it's used on larger projects but can it be used on the smaller ones as well?

I have a right angle prism and a double right angle prism. The right angle prism was made in the 1950s. Its good for finding 90° and for perpendicular offsets. The double right angle prism is the modern version that is popular. With it you can do the same as above and you can also get on line between to distant points. You can't do that without the aid of a double right angle prism or an aiming device. Very handy for setting fence posts between corner posts without having to stretch a line. We surveyors use them for marking property lines and such.

Cool, nice bit of kit never seen one before! I do like the Kubota cap 👌👍

New to the channel, enjoy it very much and learning some valuable things as well. Thanks for that! And one of the first videos I see has a question I could answer.... I used a right angle prism for 30 plus years as a field agronomist. I used it for laying out and squaring up research plots when they were going to be planted in irregular shaped fields. Now, with GPS enabled planting and harvesting equipment and all other location & monitoring technologies, it has kind of made the prism a bit less useful, but I still use on other projects.... Be well!

Thanks bro!!!!! I have had one of those for quite a while in my tool pile and I really never knew what it was for. I thought it was something complicated only usable by surveyors and dependent upon other equipment.

Used one for years surveying gas pipe lines for Texas Eastern. Usually hung a plumb bob from the bottom.

Cool. I worked on a pipeline in Montrose pa for awhile.after I retired.keep up the good work

I'm going to get one. Looks like it comes in handy. Thanks for sharing.

Mike love the channel and I don't think I have ever seen this device before today. My stepfather used to build ponds for folks around here and he used to use a transit device.

I'VE NEVER EVEN HEARD OF A RIGHT ANGLE PRISM BUT I'M GOING TO GET ONE. THANKS MIKE.

My Dad was a farmer and part time carpenter while I was growing up in the 50's. He had one of those and used it to square up barns and other buildings he was building. He also used it to shoot fence lines, whether a straight line or 90 degree angle.

I have not seen this prism type before. This should save a lot of time on large dimension projects like setting corner posts and setting posts for cross fences. Thanks for the link

I learn something in almost all your videos .........this time was no exception!!!!!

Nice man, thanks! I'll get one for my new project 211 plots! speaking of which did I miss your decision or should I load up the excavator for a road trip? LOL

@OutdoorsWithTheMorgans

6 жыл бұрын

Kapper Outdoors, Haven't decided yet, well I should say haven't decided how big of a food plot yet lol

No never have but looks like a great tool to have, thanks for sharing

Heard of that instrument but never had one or saw one live. A nice piece of gear and would be very useful for outside work.

Thanks for the video Mike! I have never seen one of these before.

That’s a pretty slick tool. Might have to look into that. I use a theodolite for most of my projects but that would be great for things you suggest. Thanks for sharing. Hadn’t seen one before this.

Good morning from St John Parish, Louisiana. That was the first time I have ever seen or heard of a Right Angle Prism.

I worked building the Seabrook Nuke Plant in the late seventies/early eighties (there was some serious blasting done there). The surveyor teams used them on everything that was big, long, and intersected to a right angle. I could be wrong, but I think they also would shoot a laser into the prism to get right angle laser shots. I've seen them used on other large construction projects malls, parking garages,hospitals, school/universities, etc.

@talezfromthedashcam3138

6 жыл бұрын

Well, at least he's not building an AP1000...

Looks like a handy tool! Thanks for the info!

My dad was a concrete man. Poured curb and gutter and built bridges. I am almostpossative he had one in his briefcase for big layouts. Good memories.

Hi Mike.Never saw one before.pretty cool. I used to operate heavy equipment. I appreciated a good shot! Helped load some holes . I was wondering what you do now? Thanks good video.my dad was a carpenter/ fix anything.would be loved the prism

@OutdoorsWithTheMorgans

6 жыл бұрын

Oil & Gas Industry (Supervision)

My dad is a 94 year old retired building conttactor. I was going through his old transit and surveying gear and found a version of one of these an a small leather pouch. For a little while i wondered what it was until I took it outside and played with it. All his stuff dates back from the 1950s or 1960s so is 100% optics. Thanks fir the discussion of the instrument. It confirms my experimentation.

A great tool, never have seen one need to add it to my inventory!

I love simple useful little gadgets and this definitely falls in that category. Gotta have one. Thanks. By the way, who does all the editing and creating of your videos. The videos are great not just because of the content and your personality but also by the professional way they are created. I know this is an outdoor program but maybe some rainy day or two you could move indoors and create a video on editing for us dummies who would like to improve our videos a little bit. Thanks again.

I’ve never seen one before. When it comes to projects around my yard and keeping things square I just give my grandpa a call, he’s an old surveyor. That right angle prism seems pretty slick though!

@OutdoorsWithTheMorgans

6 жыл бұрын

Yea having him around to help would be even better lol

Yes I could see through it just fine. My dad was a carpenter and he had one along with numerous other tools, he would say ( you can tell how good of a craftsman was by three things, the tools they had, how used they were, how good of condition the craftsman kept them. )

That's neat. First time I have seen or heard of them. The only rare tool I have. Is a persuader. If you hit things with it hard enough, sometimes what you hit will cooperate lol.

Yes mike i have used them for efore for years building fences mine has the copper housing its that old mine was given to me by jim Stewart over in Jackson hole back in 74 and still works great today

Literally just finished building a fence tonight after three and a half weekends. Wish I would have seen this video before I started

I have never seen one of those before, but I sure could use one for laying out a garden fence project that I have!

Nice demo, my husband uses one, I steal it for the garden.

Nice handy tool......I need one at some point!

Mike, I have been on this earth for 57 1/2 years and I have never seen one of those. Handy tool.

New to me. Very cool. Thanks for sharing

I used one when I worked summers surveying I’m East Texas with the State highway dept.

Never seen one, but heard contractors talk about them! Thanks I need one!

@Twooldfartsnavigaitingyoutube

4 жыл бұрын

Buddy Simcox Go to Amazon.com

I've never seen one before. Very neat tool.

First time I have seen one......Going to pick one up!!!!

Thanks Mike, great info. Amazon out of stock today 3/24/18 of what you selected. Restock date unknown. More heavy snow here in lower Shenandoah Valley (Roanoke). Guess I will be clearing out trees until 20XX? Your vids are very helpful.

Old surveyors tool, they are cool! Surveyor should have shown you how "To Clap 90" works every time

@Elfin4

5 жыл бұрын

?

I have never seen one of these, Mike. I must have one if it's affordable for me. I'll check out your Amazon page to help you out, Lord knows you've helped me out.

I've never seen or heard of those before, cool.

I tend to be a sort of inventive type of mind, so when you were demonstrating this tool with the 90° prisms, I saw in my minds eye, an adaptation of the technology into a rifle scope, to eliminate the otherwise tunnel vision you get from that telescopic lense, similar to the rearview mirror of your car, you would have the ability to catch movement to the sides while focusing on the center site, allowing you to see almost 180° around you to increase situational awareness. This would not only be a great safety measure, but something terrific to have in both military and law-enforcement operations. If this technology already exists, I’m not yet aware of it.

Interesting... I might have a use for that tool. Does it have cross hairs in the viewer for precision placing of stakes?

Never seen one but a very interesting tool for sure!

Just ordered looks great for field fencing

@cathyoakes5533

6 жыл бұрын

£3.79 Shipping to England, Due Feb 2nd

I was wondering what that was on your Amazon Store site. Very interesting and maybe very useful.

I've had one on my measure/level/siting shelf for many years from Leitz....and the telescoping mono-pole. I don't use it for precision...however with laying a few excavation corners for clearing & scrubbing. It makes that chore pretty easy. I have used it many times for setting off side yard lines by scoping corners front to back...setting out a few intermediate stakes and then setting the Leitz up over each intermediate stake to shoot a 90° towards the lot's center. With someone holding the tape that's attached to an intermediate stake....just pull the set back, side or rear lines with the tape measure; once centered on a forward siting towards the next stake. It gives you your right angle to be exact on measuring the offset. It's a good tool with the least amount of jeopardy to hauling transits, tripods and siting rods.

What you have is also called a surveyor's cross. The ones in brass can be quite pricy. For well under $100 these newer ones are accurate to 3 minutes. Will look for one soon for rough use. Best if it is level to begin for best accuracy.

Man that sure would be handy for working on fence projects

Thank

Very cool - have not seen it, but wish I had.....

Have never seen one, pretty cool.

Just like to tell you I enjoy your channel. My wife and I are moving from Houston Pennsylvania to guys Mills Pa.And we use your channel for information.

@OutdoorsWithTheMorgans

6 жыл бұрын

Nancy Buckley, Thanks! I appreciate that

Nice gadget, never seen one of them. How can it be accurate though if there's no cross hairs in the prisms to align or find the proposed 90° line. Probably best to use a 3,4 5 rule with a laser rule for accuracy. Can you do a review and show how accurate that prism is ?

I honestly can't say whether I have or have not seen one before, as I've seen so many different niche and custom tools (mostly due to family members working in different trades) that I've rediscovered ones I've forgotten I'd known about previously. However, now that I've seen this I want one (even though I haven't a clue when I'd use it). In the interest of sharing odd/nice tools: a pallet buster is one that is very useful for completely breaking down pallets (into firewood for example) as it's far easier and faster than using a regular crowbar. Likewise wire stretchers were added to my "to-get" list for fixing barb wire fences repair as soon as I learned such a tool existed.

That tool works kinda like a cross-staff which I like even better. The Cross-staff is easy to make and easy to use. Some are made from a block of wood with two perpendicular saw groves in the top. This lets you square off a corner of land very easy. Before the transit was made back in the early days of Surveying the guys needed a way to square Acres of land. Anyway I made my own but would love to buy one that is factory made with the staff mount like yours has at the bottom. They are easy to use and good for many projects. A word about yours I did not notice any vertical lines that show the exact square that I prefer but it was pretty good. If you had one for sale made of plastic or aluminum with the perpendicular groves I would buy it in a minute.

Get you a Logox you will love it!!!

Relative the right angle prism, I went to your Amazon site and there are 2 right angle prisms, one for $29.99 and one for $59.99. Do you have a suggestion, I am not familiar with either but I think that would be a great tool to have

That's a new one... we've been spoiled with quick math and laser beams! Thank you for sharing.

Hey Mike I'm guessing you've been busy lately. Waiting patiently for your next video. Hope all is well.

Yessir, works great, no moving parts, and no USB port. ;)

Udes one of those when surveying years ago.

Hi I just would like to know what camera you use for your videos? Interesting channel, go on!

@OutdoorsWithTheMorgans

6 жыл бұрын

Erik N, Here you go kzread.info/dash/bejne/rIuBlbuxg5fKlps.html

Never even heard about the thing until today.

Hi. I'm not able to accurately use this gadget on site. Yes I can locate right angles but i can't really tell if the ranging rods are dead on for accuracy. I wish it had vertical hair line to help obtain exact points.

It must cost a small fortune to keep feed in that feeder!! 👊

Dad used 6 , 8, 10 to find 90 degrees to square up a string line for new building.

Licensed blaster, my brother in law’s are blaster, majority of there blasting is in blue stone quarries deposit ny and into Pennsylvania. They have in the past blasted for gas lines or pads I believe. Anyhow good video.

2:35

never saw one ,wish i had that when i put my fences in

COOL JOB .BLASTER ,get to blow stuff up!

Yes, actually I have seen one of those before. I did NOT know what it was for though.

I use one for setting up corn and soybean fields for work.

Do they make a left angle prism.

Have one for many year. If you own land/property it simplify everything.

What do you feed deer?

According to Amazon these are called, a ‘XGeneology double right angle prism’. They sell for around $50.

I get my blaster here in kentucky a nice Xmas present every year because without him my life would be hell trying to beat & rip rock out with d10s and 385s

I have all wanted to be a blaster I love blowing stuff up!!!

Never seen them before in the UK 🇬🇧

Not sure about in your feeders but make friends with beer makers and take their spent grain. It's great animal feed and compost. I don't think it's as shelf stable as the corn you're buying but it would be free and befriending a beer maker could get you free beer also.

@mooman86

6 жыл бұрын

wauhawk buddies of mine use it for their cattle

Did you work on I-68?

@OutdoorsWithTheMorgans

6 жыл бұрын

No, but pretty nice rock cuts on 68

I want one. No need for just want it. 🙂

Being paid to blow things up!? Talk about a dream job lol! Sweet tool.

IV heard of that tool but never seen one.

how many chickens do yall have? are they good egg layers?

@OutdoorsWithTheMorgans

6 жыл бұрын

13 and yes good layers

New to me.

Never seen before.

Blaster to for strip mine lot of responsibility for 20 years let it go to younger people last working years foreman RETRIED that 90 degrees thing would been big help

Hey i was that kid who asked about your truck tonight, wiuth those 3 other kids. Just wanted to say hi

@OutdoorsWithTheMorgans

6 жыл бұрын

Hah! Thanks!

@BobDogs

6 жыл бұрын

I just wanted to tell you that i was that kid... congrats on the 15.4k subs hope you the best

What are you feeding the deer?

@OutdoorsWithTheMorgans

6 жыл бұрын

Corn

@gregodaniel7284

6 жыл бұрын

Outdoors With The Morgans didn’t hear the part where you said feed chickens my bad