NEW VIDEO based on your comments 8 Tools Under $20 YOU Said to Buy - kzread.info/dash/bejne/iphkrMylgtnJXbg.html

@buzzbbird

Жыл бұрын

link for the 1-2-3 blocks?

@douggauthier4768

Жыл бұрын

Mastercraft utility blade us cool asf, knife to scraper is awesome

Possibly the most obvious "must have under $20" is the speed square. Straight lines, angles, short measurements, it can do a lot. And not just for drawing the straight line but you can also butt the sideplate of your jigsaw or circular saw against it for perfectly square cuts. Depending on the size you can also get a contour duplicator for under $20 and this is an invaluable tool if you find yourself needing to make a complex cut to fit around something. A couple more great tools to have on hand that you can usually find really cheap (even dollar stores will have them) is sanding sponges and sponge brushes. Sanding sponges are great for contours as they mold into the shape pretty well while still keeping fairly even pressure throughout. And sponge brushes are useful for applying stain, clearcoat, and higher viscosity paints that tend to dribble off of bristle brushes. And as someone who has had wood chips, sawdust, and flakes of fiberglass fly into his eye while working on various projects over the years easily the most important tool you can get for under $20 is a good pair of safety goggles and/or a plastic face shield. Yea, these aren't as "cool" or "fun" as a lot of other tools out there but it's far better to look dorky than to have fragments scratching your eyeball from the inside.

I would add 1-2-3 blocks to this list. SUPER useful, and you can pick one up for ~$20.

@Fixthisbuildthat

2 жыл бұрын

Great addition!

@Alex-rf1md

2 жыл бұрын

I love 1-2-3 and metric 25-50-75 blocks, they can space, act as a small straight edge or square and a lot more

I found that the claw device works really well for unclogging sink & tub drains.

@andrew_gardner

2 жыл бұрын

Just scary the things they'll pull out, hair collects some funky friends in a bathroom sink haha

@Fixthisbuildthat

2 жыл бұрын

I love those plastic pull strips with the teeth too

@williamellis8993

2 жыл бұрын

That claw device is marketed by Menards as a drain clog remover.

You'd be surprised how many things from the craft room are helpful in the woodshop (and vice versa). When I upgraded some of my quilting rulers to some that don't slide on fabric as easily, I took the old ones to the shop. They are awesome! You can see through them to line up marks, they have graph dotted lines all the way across them, 3 to 5 inches wide and the longest ones I took out there are 24 and 36 inches long! I also have some tiny ones too. They also have several angles marked on them as well. Additionally, I find washi tape, repositionable double sided tape, and card stock handy in the woodshop.

@Elymyntal

2 жыл бұрын

I love your quilting ruler tip MissBeans, it's actually brilliant! Now I have even more reasons "caugh" excuses to go quilting ruler shopping :)

@TheLovelyMissBeans

2 жыл бұрын

@@Elymyntal glad to help! 🤭

Why take a tape measure to the hardware store? I just grab one off the shelf real fast if I need to measure something🤷‍♂️😂

@Fixthisbuildthat

2 жыл бұрын

Oh yeah, I've done that a time or two or ten 😂

@JCWren

2 жыл бұрын

In the Lowe's I frequent, the lumber department is at one end of the store, and the hand tools (like tape measures) are at the far end. While exercise is a good thing, I'd rather not have to trot across the store just to grab a tape measure. So, yeah, I take one with me.

@comsigninc

2 жыл бұрын

Just don’t instinctively put it in your pocket..

@akbychoice

2 жыл бұрын

So you are the guy that leaves the tape measures all over the place.

@natemartinez4595

Жыл бұрын

Sometimes the tapes are on the other side of the store

Used the extended claw in the Air Force all the time. We called them "mechanical fingers" and they're great for grabbing stuff from the deep dark corners of an F-16 cockpit... I'm reliably informed lol

@Fixthisbuildthat

2 жыл бұрын

hahaha, I can only imagine. Thank you for your service!

@jonnyjl345k7

2 жыл бұрын

That moment of shame and embarrassment when you have to ask someone on the ground to hand you the fingers, magnet, and a mirror…

@andrew_gardner

2 жыл бұрын

@@jonnyjl345k7 I always loved when you go after a bolt and pull out two nuts and some safety wire instead

@muhhamad786

2 жыл бұрын

@@andrew_gardner Will have to do the echo test to find it? 😂

@jaypeay1941

2 жыл бұрын

I too was in the USAF and used the claw tool. Worked on radar set on F-101 fighter. It had a shelf that some of our radar equipment sat on that was in the nose cone. Amazing how many tools I was able to find under there with the claw.

One of my favorite less expensive tools is the Nicholson 4 in Hand rasp/file. It has always been in my tool set whether I need to clean up a notch in wood, smooth an edge of sheetrock, or sharpen a point.

Definitely in the "Get you weird looks" category: Trashy red lipstick. Seriously, you can use it as transfer paint for marking mounting holes to walls. Dab a bit on the keyhole mounts and press (kiss) it to the wall, pull away. And your marks (smooches) will show you exactly where to put those mounting screws.

@marvthecarpenter

2 жыл бұрын

This tip also works really well for marking doors when the latch and strike plate are misaligned. However I've been told not to get too cheap as they are waxy and won't actually transfer anything, and the pricy ones are made to not come off. You gotta find that happy place in the middle.

@Chhesterification

2 жыл бұрын

@@marvthecarpenter brand: Revlon color: cherries in the snow That's a classic red lipstick.

@lancelavallee8119

2 жыл бұрын

I use ketchup, mustard, or mayonnaise packets. Depending on colour I Ned to apply to.

The other end of that spring loaded nail set is actually a center punch, replacing the next tool on your list 😎

@Fixthisbuildthat

2 жыл бұрын

they make that version as well. Mine is double nail sets. Now I wish I had the other one, lol

I keep plastic straws on hand to help clean squeeze out for glue/finish in tight corners

Painters 5-way. I'm not a painter, but this tool is so versatile. I use it every day. It does so much. Once you start using one, you'll wonder how you functioned with out it before. I'm 40 years in construction. Have to say this is the tool I make sure is in my pouch.

@garyoa1

Жыл бұрын

Agreed. I do a lot of finish work so I never realized how much I needed this gadget. Sure beats a screwdriver for opening a can of poly. (that blew me away) Not to mention it's other uses. There's a reason it's called a 5 way. 😃

4 of these items can be had from dollar general, dollar tree, family dollar, or just about any dollar store... The pop sticks, the syringes, the snapoff blade knife, a screw driver. I agree with this vid, as i have used 18 of these items as mainstay tools and implements that can be had for under $20....

All great pics but I have to say Handy shims are simply amazing!!!! you get for different sizes and are extremely useful when doing cabinet drawers. I have them all over my shop and they are cheap and reuseable!. LOVE YOUR CHANNEL! Thanks so much for all the inspiration and education you continue to bring to this maker community!!!!

I too got an ice pick from my grandpa when he passed.

Rare earth magnet stud finder. Best tool ever.

The tongue depressor idea got me to thinking, for years I've kept a box of wooden toothpicks around the shop (flat and round), as well as a bag of bamboo skewers (like round toothpicks, only bigger) and wooden coffee stirrers (like skinny popsicle sticks). These all have a variety of uses, with mixing, filling, even small-project doweling.

@stuartbennett1163

2 жыл бұрын

i like to use ice-cream sticks in the UK. after the kids have eaten the ice-cream i just was the wooden sticks and they are really usefull for stirring and absolutely free

@gamer2101

2 жыл бұрын

I use wooden coffee stirrers like crazy. They are so helpful

A transfer punch is nice to have. I just bought a set from harbor freight for $9. I always have trouble transferring the exact center of a hole on to wood/metal for caster or a name plate and those put the indent smack dab in the center.

+1 to the ice-pick. use it ALL the time.

I call the claw pick up tool "the total recall" tool

Coffee stirrers are also highly useful. You can of course stir and mix with them, but you can also use them in model making for anything wooden like little crates, walls or roof shingles.

@codacreator6162

Жыл бұрын

The advantage to coffee stirrers is you can always use them for coffee if nothing else. 😀

@johnnieblackburn3182

11 ай бұрын

Packs of popsicle sticks from the dollar store are great stirrers for smaller needs.

I work at an assembly line building industrial trailers so I need heavy duty tools, but I work in both framing and finishing. Wearing a belt while doing finishing work is a pain, so this list of handy simple tools is great. All of this can fit in my pants side pockets

@Fixthisbuildthat

2 жыл бұрын

yes, I love the small gems

saw the picture, saw the green pencil, looked in my toolbox. Its one of my alltime favs!

Hey, Brad. I enjoyed your practical selection of cheap tools. For mixing stuff in small containers, I use plastic knives. Anyone who uses plastic flatware for get-togethers, picnics, etc., buys a combo package of forks/spoons/knives. The forks and spoons get used, but the knives just sit there. So, I ask for the (inevitable) left-over knives and have never needed to spend any of my hard earned cash for them. They are just the right size and stiffness. Also, the back side is slightly less rounded and can scrape the corners of your container. Try it out.

@michaelgriffith3385

2 жыл бұрын

I use chopsticks I have left over from Chinese food. Great for mixing, stirring stain, etc.

@lancelavallee8119

2 жыл бұрын

The spoons and forks have used as well. The spoons are great for molding caulk and other applications, like Bondo for repairs. The fork tins cut off work great for filling stripped screw holes.

@BillLaBrie

Жыл бұрын

If you’re near an ikea, their “baby flatware” sets are worth the minimal cost. I use the knife and spoon for almost everything from spreading epoxy to separating parts without scratching them. They’re sturdy and won’t shatter.

As far as using the claw to reach for things, I just used mine yesterday (1/2/2022) doing some wiring for my brother in his Toyota FJ. However, I did not use it to reach for things...I used as a fish t help run wires in and up under his dash. Came in really handy and made the project go along much easier. With the snap off blade/cutter, I get mine from Harbor Freight. Comes in a 3 pack of different sizes, or you can get each one individually. Good tips!

Definitely add Dental scraper/picks. They are handy for everything and come in different shapes. If you ask you dental office they will usually give you ones that one side broke for free. I use them way more than ice picks. They are great for woodworking and mechanic work. You can even get them brand new at princess auto for about $3 each but they are not the quality of a dentists office ones

@TheLovelyMissBeans

2 жыл бұрын

I'll be darned. I would never have thought about that!

@Fixthisbuildthat

2 жыл бұрын

Clever, I like that

A stud finder is a great tool to have

Auto-hole punch is a great tool. Also really good for keeping in your car for emergencies. Used to be an aircraft engineer in the Navy, and these auto hole punches are ideal for metal work, but also for breaking through strengthened glass in an emergency without a hammer and in a tight place where you can’t swing one. Worked crash rescue and it is a really handy to get through a window in an emergency .

@sircurlyfries1326

Жыл бұрын

great... your telling everyone ez ways to break windows

For the tongue depressor: Get your household a nice set of metal chopsticks and save the wooden chopsticks from takeout. They make for the best fine mixing tools. They're tapered on one end and flat on the other.

@Fixthisbuildthat

2 жыл бұрын

Nice tip! I have some chopsticks form my travel in China that I always use. Just don't eat enough Chinese takeout :)

If you like the snap blade knife, check out the ones made by Olfa. I've had one for well over 20 years and it's still going strong.

@Fixthisbuildthat

2 жыл бұрын

yeah, I've heard Olfa is nice

That irwin saw is DA BOMB. It's absolutely worth every penny and twice that.

Papermate Sharpwriter pencils. -Cheap -Disposable -“spring loaded” tip prevents premature breakage. Best I’ve found.

One of my most used "tools" is a scrap piece of leather that I use as a strop. It cost less than $5 and I can use it on a flat surface to hone my chisels or curve it to work on my carving gouges.

Great ideas, Brad! I pick up old hand mixer blades at yard sales, Goodwill and similar other second hand stores. They are great in a cordless drill for mixing small amounts of drywall compound is a mud tray, larger batches of two part epoxy in a coffee can or other two part compounds. The nice part is they are cheap, so if lost or ruined, they are easily replaceable from my box of spares.

@squarelevelplumb

2 жыл бұрын

I used them in my drill press for mixing paint.

@MrTPF1

Жыл бұрын

Oh -- so you're not supposed to use your wife's mixer and clean it up real good before she gets home? LOL!!

@mcouture8169

Жыл бұрын

@@MrTPF1 That video would appear on the "Break This Divorce That" KZread channel.

I use a lot a Reveal Marking Gauge. It’s under $20 and save me time.

One of my favorite cheap toolsis Milwaukee 6 ft. Keychain Tape. It has both metric and imperial and is super compact and less than five bucks. Another great tape is self lock evolution tape - all tapes should be like that!

Straws! For getting glue out of tight spaces. Loved your ideas and already apply many of them. I’m adding that pencil to my wishlist. Thanks!

Awesome tips along with these cheap tools thank you. And well done on trying to use the metric system 🙂

That mechanical pencil is essentially a drafting pencil with a holster. I like it.

14-1 painters tool is the best tool I’ve ever owned. So versatile

Thanks for this video. I already have most of these. Two items that are a must in my workshop are Magnetic Parts Holder Bowls (4 inch or 6 inch are very handy) and a Magnetic Tool Holder (18 inch(. Both are used to keep small tools, screws, drill bits, etc. handy when I am working on a project. I also keep the small syringes that I get from the vet for giving meds to my pets. Very handy.

I have an old "lead holder" drafting pencil that I like to use in the shop. I got it at least 30 years ago with a sharpener. In my college town, it's really easy to get refills for it. For folks in the Midwest, your local farm supply store is a great place to find inexpensive syringes with various guage needles. They're handy for squeezing in glue where you need it as well. Thanks for sharing!

@Fixthisbuildthat

2 жыл бұрын

sounds cool

@HickLif3

2 жыл бұрын

Drafting pencils are also a lot less bulky too. they're awesome

Best tool for under $20 I have ever found is my little Pencil Zingy! It attaches to a construction pencil with a retractable string so I never lose my pencil again! Might be the best tool I own!

I don't know if someone else has said it, but the Pica is also very good to mark through a hole, especially if you need to mount something to the wall. The small shaft makes it really easy (given that the hole is big enough).

@normferguson2769

Жыл бұрын

50 years ago we used that same pencil leads in mechanical pencils for drafting. Good to see someone has reinvented the concept for woodworkers!

For mechanical pencils try the uni brand. They rotate the lead every time you lift up to draw another line and a retracting support tube to reduce lead breakage. I like the Kuru Toga and Shift Pipe. That Dewalt tape measure is stuck to the case or stand on every machine in my shop. While I wouldn't rely on it for precision marking it is great quickly double checking rough setup.

@TheHeadincharge

2 жыл бұрын

Also a nice, thick 1.3 mm mechanical pencil is quite useful for basic marking as well. Almost impossible to break unless extended super far. The kikuyu enpitsu mx is really nice for this and solid.

That screwdriver from your grandfathers is, if I’m not mistaken called a perfect handle screwdriver. I saw somebody do a restoration on one once on KZread. You’re right. There are a tank. Heavy duty metal blades full length tangs and the handle shape is tremendous. Allows a good grip and gives good leverage. They’re quite collectible as I recall. Of course I know you’re not going to sell your grandfathers. I’ve got a bunch of my grandfathers tools in my basement. I hardly ever use them, but I love seeing them and knowing that they’re there. Reconnect me to him a little bit as we spent some time in the shop at his house.

@icekohl

2 жыл бұрын

Hand Tool Rescue makes giant new ones.

@chucknorris2952

5 ай бұрын

Have an old one (think 30s). The word "phoenix" is stamped on it, in tiny letters. Found it while i was digging outside my house. It sits very good in the hand, as you said👍

I got a retractable exacto knife I find myself using a lot more then I expected

I have these Pica pencils and absolutely love them. Liked them so much I bought a second pair of them as a gift to a woodworker friend and backup for myself. He loved it as well. Thanks Brad.

I would add a 1-2-3 Block and I am surprised you didn’t mention this, a small notebook. I use this for writing ANY measurements down when I am walking back and forth in the shop or running to Lowes for things.

@Fixthisbuildthat

2 жыл бұрын

I've gotta grab one of those 1-2-3 blocks, don't have one

@Not_TVs_Frank

2 жыл бұрын

@@Fixthisbuildthat Wen sells an inexpensive 1-2-3 set. They are meant for metalwork, so that means that even the jankiest ones are precise enough for woodworking.

Great ideas for things we can't live without!!! I've got many of these already and just got the Pica Pencil and white leads for Christmas. I've put several of your ideas on my wish list and will be purchasing them. Thanks for the tips!

@Fixthisbuildthat

2 жыл бұрын

thanks, Lori!

@bobmeister51

2 жыл бұрын

Pica Pencils are great especially the different colors. However when you drop the pencil the black lead will break.

@SawdustmakerLori

2 жыл бұрын

@@bobmeister51 Thanks for the info! I'll have to be careful not to drop the pencil. I work a lot with walnut so I'm especially looking forward to using the white leads. Have been getting white art pencils but they don't stay sharp long at all.

Spring loaded nailset will work as a center punch also.

Really excellent tips, Brad! Thanks a lot! 😃 What I like to keep around is one of those BIG syringes (I don't know, they must be more than 1 inch thick) with grease for the machines. It usually comes with a plastic tip that closes it very well. Anyway, stay safe there with your family! 🖖😊

@Fixthisbuildthat

2 жыл бұрын

great tip, Happy New Year!

Brad, great ideas. I bought a simple tire tread depth guage a few years ago. I use it to measure hole depths when drilling and it comes in handy for several other purposes. Probably can pick one up at the auto parts store for $5 or less. Jaypeay

@BobboMax1

2 жыл бұрын

I favor an old-fashioned folding rule for a depth gauge- the fancy ones have a little sliding ruler built in. Also handy for getting accurate inside measurements. And it fits conveniently in the lower left hand pocket of Carhartts.

@Fixthisbuildthat

2 жыл бұрын

What a clever idea!

@Sadowsky46

2 жыл бұрын

Why not use calipers for depth measurements?

@tof3275

Жыл бұрын

Use a quarter, and stick it in the tire groove which should cover the raised edge, IF you can see the raised edge then it's time to renew that tire, cheaper than a $5 gauge and you get to keep the quarter.

Great tip on the syringes...I guess in this case literally. I'm doing some chip carving that I wanted to try filling in with colored epoxy and I think you just saved me from making a huge mess! And I'll double down on the vintage ice picks. I find these all the time at tool swaps in that nasty bucket of crap for $1. I love em.

Well, this damn video cost me $180! Really good recommendations and links, thanks!

Drillblock. I think its like $12 on amazon.

Excellent video Brad! Happy New Year to you and your family! Be well and stay safe! Looking forward to what you have in store for us this year. 👍👍🔨🔨

@Fixthisbuildthat

2 жыл бұрын

Happy New Year, Steve!

The day is started woodworking was the day i started making my own stir sticks for mixing. Always a scrap around to be used for that purpose. :)

@Fixthisbuildthat

2 жыл бұрын

The day I bought stir sticks was the day I cleaned up my scraps, hahaha

@glennryzebol4472

2 жыл бұрын

@@Fixthisbuildthat lol. Nice.

Your were half way thru and I hadda hit the subscribe button so I wouldn't forget. I watch plenty DIY and woodworking shows and I found you very knowledgeable and entertaining. I do pick up tips and techniques that I in turn use. I will be watching more of you.

You can get jumbo paddle pop sticks for $2 aud at cheap shops and craft stores so that’s probably a cheaper option to consider

Stanley 33-115 10-ft tape measure. It fits in your watch pocket, so you actually have it with you most of the time. And, it has a diameter scale on the back, so you can check pipes, etc. One, comment on the syringes: the more viscous the fluid the smaller syringe you want, with a larger bore, smaller number size, needle. A syringe that is twice as big takes four times as much push on the plunger to develop the same internal pressure. Because when you double the size the area increase by the square of the 2, giving an area 4 times as large.

Brad, I also use syringes for intricate glue applications. They are great if you inadvertently wind up with a small crack or opening where it's hard to apply glue. Thanks for all the tips.

@lafamillecarrington

2 жыл бұрын

Syringes are so useful - I have a range of sizes from 1ml to 50ml

@user1111AB

Жыл бұрын

that pencil in the thumbnail is absolute trash breaks after one week never buy

As a mechanic, the magnet and grabber have saved me so many times.

Great tool ideas here. You're definitely one of my top 3 favorite channels. I like the info and your personality. Thanks!

I have the spring set and the back side is for center punching. Given how often I use the nail set part, I think the punch/set combo is better.

Great video thanks! I’m always looking for the perfect gift for my father. He enjoys wood working and has all the tools he needs.However, these “gadgets” are unusual or used in unusual ways and so would make a great little gift basket. Maybe I’ll even couple the basket (probably small tool box) with a link to your video. I’m definitely gonna get my woodworkers gift box going. Thanks again for the gift inspiration! And thanks to your followers- Looking through the comments for more ideas to add.

This is proving really useful for figuring out what a bunch of the "what IS this thing" and/or "how are you supposed to use this?" going through second hand shops and the shop that sells broken packages and returned items.

Just ordered the marker! Really clever device. Thanks!

A good utility knife is a must! My favorite is the Olfa XH-1 as it has a rachet lock for the blade. Absolutly won't slip open or closed.

@greekveteran2715

4 ай бұрын

Olfa XH-1 can also use their 25mm saw blades, that are both flash saws, and general use saws, for different materials and not only wood! Great for plumbers, woodworkers even painters can use this from time to time. I love Olfa, they are tthe inventors of the snap of blades, so I guess they aere easily the best brand! Only problem is, which utility knife to get,because they make a ton of different styles, that all do one or 2 more jobs, that the other snap of utility knives don't!! PS They also make the blade saws, in 18mm but be careful, because these look very similar, to their serated blades, which is a completely different style of blade.

For really small (Dixie cup or smaller) mixing, I use coffee stir sticks (wood, not plastic) even less waste than popsicle (senior tongue depressor) sticks.

I literally bought that deWalt 9’ tape measure a couple weeks ago for the same purpose. It’s awesome for measuring furniture in a store to determine if it’ll fit your space. Just measure the space before you go to the store, throw it in your pocket and off you go!

Bought a few items as a result of this video, very helpful, thank you!

Brad great video, my husband uses flat and round toothpicks, flat to spread glue inside wooden wheels, the round as small dowels, also he uses yougart cups to put wipe on poly or water based paint like delta cream coat or folk art brand when this dries in the cups you can simply peel it out and reuse these again

I do carry a small tape when I'm out thrifting. I would suggest getting the disposable box knives from harbor freight. They're much cheaper and the quality and comfort of use seem to be on par. Also check out the 3 inch circular saws. They're about 20 for most brands and work great for small projects and tasks. I do a lot of trim work and it's super handy to make small adjustments without traipsing out to the big saw to adjust a bit of chair rail by a small fraction.

i believe that flexible claw is designed for pulling hair from drains but i could be wrong

Very helpful video! 👍I bought one of those pencils off your recommendation. Had no idea such a thing existed but have always been frustrated with spindly leads breaking. Works great!

Some great stuff there Brad. Another awesome mechanical pencil that I would highly recommend you check out is the Pentel Graph Gear 1000 mechanical pencil, you can get in various led sizes. What’s I find is especially nice about them is that the little metal tip at the end that the led comes out from can be retracted by pushing the clip so should you drop the pencil you don’t have to worry about it being ruined from the tip being bent or broken off. I’ll definitely be picking up one of those mechanical pencils that you showed however as I like the idea of the much larger led and the option of different colored leds, I’m sure that they are great for on rough wood. Thanks for sharing.

@coreylahey7344

2 жыл бұрын

true, i use something similar to what you're talking about. I have a 5.6mm mechanical pencil, found 2 of them for $12 on amazon. very nice to mark with and it's basically impossible to snap the lead,

@carlcox7332

2 жыл бұрын

Those 2mm mechanical lead holders are also great when you need to transfer/ mark hole locations through existing holes. They're actually marketed for that specific purpose on Amazon.

There is a hardware version of the icepick called a scratching awl. They are similar in build and look, and can be bought relatively cheap ($5-6 on Amazon). Some other tools I use a lot and are pretty cheap are some calipers and a compass.

@mpmfr

2 жыл бұрын

You may also look for a pick tool (or as the cringy name, dental tools). Very helpful to have around the shop/home. 🤟😎👍

@Fixthisbuildthat

2 жыл бұрын

Great tip, thx

I just bought 75% of this list and it's so cheap there's no guilt. Thanks!

At Harbor Freight they have a handy tool, Acid Brush. You can get a bag of 36 of them for under $3.00. It’s a 1/2” horse hair brush that is great for spreading small amounts of glue, paint, etc. and affordable enough to toss when done.

An icepick is very useful for starting screw holes exactly where you want them, as well as marking locations for them. I keep one handy at all times.

@theRhinsRanger

2 жыл бұрын

Theres a shop tool for this, an Awl

@oddoneout1835

Жыл бұрын

Under $20 though? I'm not looking this up.😗

Brad, check out the flush cut saw that JKM sells. It has a zero tooth set so that it doesn't scratch up the piece you are cutting against. I love mine!

Simply great video! Thanks!

Love it when a Brad asks, "What's in the box?"

Brad, small craft stick/popcycle sticks are great stirrers also. A bar of soap for screw lubrication. I have a magnetic wristband to put nail screws bits at a reach. Small LED flashlights for people like me with aging eyesight. You can do a new segment of viewer suggestions. love your shop and builds.

Great tip on the mini tape measures! Just this morning as I was trying to find mine and was thinking “why the heck don’t I just buy a few more??”

@Fixthisbuildthat

2 жыл бұрын

Oh yeah, I bought one then bought three more, lol

Bought a pica dry pencil and some refills with mixed colors, love this thing.

Bought the pica pencil set as stocking stuffer for my daughter, in electrician apprenticeship program, and one for my son, who is a heavy equipment operator owns own business. They both read reviews and stated will definitely come in handy.

The spring loaded nail set is awesome. They make one that’s more like a flat punch specifically for door hinges also.

I buy six-inch tounge depressers at the craft store. I think they're cheaper than medical-grade.

@Fixthisbuildthat

2 жыл бұрын

Good call

@billymachner7551

2 жыл бұрын

You can buy silicone covered ones that are reusable too.

A good tool is a 7in. Rafting square! can't go without it!

Definitely look into the Pica pencil, advantage of having the white is great.

Great video, always like to see alternate uses for tools. Favorite tape measure is the 16' Fastcap. Length covers everything I do and the built in pencil sharpener is a plus. The front face also has a writing surface in case you need to write measurements. My favorite pencils are the Pentel Graphgear. You can get them from a .3 - 1.0 lead size. The thinnest I use is a .5, which doesn't work as well on rougher wood. I am leaning heavily towards a marking knife as part of my collection. Love my center punch, I am now going to look for an ice pick. I have ideas for additional uses for it. I usually keep short thin cut-off pieces for my stir sticks. I have an old poster tube cap I store them in. Syringes for epoxy is an awesome method. I used that technique when making coasters that had a split down the enter that resembled a lightning bolt. Keeps the epoxy where you want it 👍 Thanks for the great content.

@Fixthisbuildthat

2 жыл бұрын

I recently picked up a FastCap fractional/metric combo tape and it's great

@pantherman4699

6 ай бұрын

@@FixthisbuildthatI have a FastCap PSSR25 25 Foot Lefty/Righty Measuring Tape - I love that I can measure on either side of it. I never use metric, so it works well for me. ;)

A magnetizer demagnetizer is an awesome tool under $10.

So fun tidbit, I have "The Claw" but it has a magnet at the end. It is the best of both worlds.

I use my telescoping magnet tool in my office a lot. They’re good for trying to thread cables up between the wall and desk.

Thanks for the great ideas. I noticed that you could save your pencil sharpness if you learned a skill that used to be used by draftsmen, architects, designers, etc., though I suspect that now they use computers instead. If every time you draw a line with a pencil you spin the pencil between your fingers, you will get a more precise pencil line and maintain the sharp point longer. Once you learn the technique, you'll find yourself spinning the pencil naturally.

@timdouglass9831

Жыл бұрын

Great tip! When I learned mechanical drawing back in the dark ages we were taught to file a flat side on the pencil lead. That flat went against the straightedge so your line was exactly on the edge. We had little popsicle-stick-like things with fine sandpaper on them for a quick touch-up. I don't know if that was a common practice, but spinning the pencil sounds like a simpler solution.

@texputter7928

Жыл бұрын

@@timdouglass9831 I found my old drafting sandpaper stick (from 1970) when we cleaned out the barn last year, but I couldn't even remember what it was for. Thanks for reminding me!😃

I like the idea of using one of those spring nailsets for removing hinge pins. Not having to swing a hammer next to a door is well worth the price of admission.

@69injunjoe

2 жыл бұрын

Good luck with that. The Tool looks weak .

@BobboMax1

2 жыл бұрын

@@69injunjoe I've always been skeptical about those spring nailsets, but they seem to work and if they do, they look a lot easier than a hammer and standard nailset. If the spring ones can sink a 15 gauge nail, it seems reasonable they can loosen and drive a hinge pin. I'll let you know...

@69injunjoe

2 жыл бұрын

@@BobboMax1 I find the current pre-hung doors from the box stores are all twisted and never square anymore. Hinges are all under stress from poor workmanship.

@69injunjoe

2 жыл бұрын

Out of 12 doors had to return 3 for improper hinge depth from top to bottom. Poor workmanship.

@BobboMax1

2 жыл бұрын

@@69injunjoe Ahhh, but the good news is those 5/8 finger-joint jambs are so flexible that it's easy to warp them straight, plumb and square again if you have enough shims and time.

Use the center punch to drive the nails

A great cheap penetrating wood finish for small project is leather dye. It goes on really well and gives you a deep penetrating finish. You can get something like Fiebing's Leather dye for $10.