I was doing an Electronics lab and didn't know what coupling meant, this helped a lot! Thanks.

I can't tell you how many "light-bulb" moments I've had watching your channel, even going back 12 years now since this was published.

Once again, an incredibly understandable explanation. Thank you !

Excellent! Excellent! Excellent! I'm a novice elect. hobbyist and just got a Tek 2465 scope and your video series is just what I need to understand and use the scope to its fullest potential!

not only explained AC/DC coupling, but also clarified couple more concepts for me)

I absolutely love your videos! You are so clear, detailed and to-the-point. This is excellent teaching.

Mind blowingly elegantly descriptive work. I can feel brain cells growing already!

Watched so many videos about using oscilloscopes , even I know how to use it and using it on daily basis. But I always love to find something new for me. Even this is not so new for me if at all after this video I have so high feeling that I have learned something new. Really god explained and showed. I wish there is more teachers like you are at KZread. . Huge thumbs up from me I wish I can give more thumbs.

Good explaining of coupling Ac and DC signal. Basically: DC coupling: both DC [bias] and AC ripple to show AC coupling: AC only This is essentially he same as the AC and DC mode on a DVM meter. But your dem is valuable as a visual proof. Thank you.

I thought, "Perfect timing." I had just started to raise the questions to the answers you gave in the video. Then I scrolled down and saw it was from eight years ago. So you are actually ahead of schedule! Thank you!

Great video. Lab-based circuits videos are particularly helpful to me, because theory only gets you so far before the practical models that were ignored/simplified come back to haunt you. Thank you for your willingness to share your insight! Also, if anyone has any other practical electronics channels that they'd recommend, I am open to suggestions. Using AC coupling to look at the ripple of a DC signal from a rectifying circuit, reminded me of my Circuits and Measurements Lab. In one lab, we needed to look at the ripple from turning on the power supply, so we had to be in AC coupling and take a "snapshot" by using the RUN/STOP mode instead of AUTO.

@w2aew

7 жыл бұрын

I'm glad you like the video. There are more than 250 more on my channel. Other channels I'd recommend are The Signal Path, EEVBlog, Afrotechmods, devttys0, Mr. Carlson's Lab and Great Scott!

So many lights buld moments watching this video, thank you!

THIS IS VERY INTUITIVE EXPLAINATION OF AC AND DC COUPLING.THANKS

love your videos! simple, short, to the point. don't get people who dislike.

I am going through your videos again. I kind of did this once before for almost the entire videos but this time, I seem to be learning much more from them. Thank you very much!

I was wondering about this today, then tuned in to your channel this evening, and hey-presto the perfect explanation ! Thank you.

I wish I had more hands, so I could give this video... 4 thumbs up! Great vid, thanks!

@w2aew

10 жыл бұрын

Thanks Matt - much appreciated!

@ki4dbk

3 жыл бұрын

What Matt said.

Excellent video and well presented. You have a nice style of presenting that talks to novice hobbyists as well as advanced techs. Keep up the good work.

Wow. Fantastic vid, put simply and clearly. This taught me a lot, thank you.

Thank you for illustrating the correct usage. A beginner here, now I can use my equipment to see what I want to see. Thanks

This was very well explained, thank you so much! Especially liked the example with the transistor/bias voltage.

Great video. Thanks. The first time I noticed ac ripple was on a car. I have been a mechanic for 25+ years. This was when I first started doing it. I only work on BMWs. I had one come in and every digital display was rolling put the meter on ac and got 2.5v ac output. I guess the bridge rectifier was going out. I part out a lot of them so I just grab one off the shelf dont repair them just pile them up and sell to the core man every 6 months.

Didn't know of that way to look at ripple, pretty cool :)

Very well explained, thank you for taking the time in explaining AC DC Coupling

Thanks, for refreshing what I have forgotten since high school. Very helpful video.

Very informative. Your videos are a great resource!

You are a master of electronics. Thanks for the great video

You are the man! all your videos are very informative i have been watching them for a month now, you are helping make sense of a lot of things. I have learned so much in the past week my brain hurts. And just got my first scope today and i am excited to start playing.. KD2GOE

@w2aew

10 жыл бұрын

Thanks for the nice comments. Good luck with the new scope, and be sure to let me know if you need a video on something to help you out!

You are an excellent instructor! Thank you!

Thank you for this video and all the insights. I like the examples. Very useful!

Great video, Alan. And I love that Simpson meter!

great video. very informative.

Very clear and very helpful, Thanks!

Great videos allen, thanks kindly!

Thank you very much! :) I got exam the day after tomorrow, your videos helped me a lot!

Excellent video

Great stuff! Keep em coming please!

Quite informative! Hopefully this explains why I wasn't seeing what I was hoping for with some DAC produced waveforms...

Great review, I needed it.

Great explanation!

Thanks for this informative video! Helped me a lot.

Great video! Thanks so much.

Great video. Thanks for the education

Excellent as always,,, thanks.

Have had several also scopes but I've never known of what the purpose of DC ground and AC coupling were. Thank you

Thank you, that was very useful.

Really well explained. Thanks

Excellent videos, thank you so much!

Awesome tutorial! Thanks so much for the clear explanation =)

Justified reason to use a "dual" trace scope! Well done! RW - KC2RDU

Jesus!!!! I just NOW understood why the group "AC/DC" is called that!!!!!! MY GOD!!!! I lived for 40 years without knowing this!!!! 😮 This is a group of electricians!!!!

Good explaing of coupling Ac and DC signal

Very good info. Thanks

Thank You man!

This is just what I need to start using my scope. I have a pile of power supplies that are not working or at least not well. I am going to need to get a isolation transformer first I think. Thanks Louis/w0it

Very interesting thanks for the vid.

Learned something new!

Nice. Thanks for explaining why.

you are phenomenal. Thanks!

@w2aew Great reply, thanks a lot. Here is another example: Say if I have a sine wave on my scope, I hit the ground to set the baseline. The if I switch the coupling from AC to DC...well, of course it has no effect. If I set a baseline and hook my scope up to a square wave, then swith the AC/DC coupling back and forth it changes things up. The DC coupling will show the total wave above the baseline (gnd-peak positive-gnd). Ac coupling will split the square wave......DOH.

Very educational.

good work!

Thank You

excellent! thanx a lot mate!

Thank ya, I need more

Great! Thank you.

really good !

Thanks, I'm doing a Linear Lab for a common emitter amp, and I thought the same as you just confirmed.

@w2aew

10 жыл бұрын

I've a number of additional videos on transistor amplifiers, including how biasing affects the class of operation, the basic configurations of CE, CC, and CB amps, and even one that looks at the frequency response characteristics of the common emitter amplifier.

Briefly in response to the previous question by revising the ground wiring of the alternator, battery and chassis connections you could avoid the ripply alternator current travelling through the chassis. However the vehicle 12v supplies will still have some ripple on them... You could research ultra-capacitors, they have very large capacitances and very low ESR.

Thank you

thank you very much.

You are such a good teacher. Thank you. I am still green as can be, do you have a vid explaining dc bias a little more? Thanks again.

@w2aew

6 жыл бұрын

DC bias is just a term that is used to describe the DC voltage that exists at any point in a circuit. Unlike digital circuits where voltages are typically high or low, analog circuits are often operated "in between". The DC bias voltages determine the circuits operating point - kind of like idling in your car.

thank you so much

Another good one. Q:What happens to the transistor during a prolonged saturation state in actual circuit applications?

Thank you for the great video! Can you explain about GND coupling? what is the purpose of the GND coupling in an oscilloscope?

@w2aew

3 жыл бұрын

GND is used to pre-charge the AC coupling capacitor for AC-coupling mode.

Fire!

Fantastic! I need a scope! Do you have any idea of why the filter capacitors in tube amps have such an effect on the sound. Many of the reissue guitar amplifiers has higher uF values after the rectification, compared to the originals from the 60's, 70's. And with higher uF values the "cleaner" DC makes the amp sound more sterile/harsh. User patfurlan has a lot of videos of filtering caps mods, for example the fender champ.

Now i understand it thanks

Great video what do you use for the AC power source?

So I think the internal capacitor simply "charges up" to the DC bias voltage and the scope's horizontal line now uses that charged up voltage as it's new zero reference point. Is that a good description of how it works?

@w2aew

3 жыл бұрын

Yes, the capacitor removes the DC content of the signal so that the signal centers around it's average value.

nice video. thanks a lot. i still have confusion. if i am feeding an AC signal superimposed on some positive dc and coupling mode is dc, i should get dc, right?(please correct if i am wrong.) but, here we see a sine in dc coupling in case of transistor. how does that happen? please explain. thank you.

🍎🌺🌺 you are 🌺🌺🌹 very clear 🌺 really an engineer 🌻🌼

@w2aew Thanks a lot for the video. What if you have a very basic scope that displays the signal with no on- screen voltmeter to show polarity of Peak pos and neg, and you have ZERO knowledge of what type of signal you have displayed on your meter....say a square wave that may be ac (peak pos-through ground-peak neg )or DC (peak pos-gnd-peak pos). How do you identify AC or DC in this situation???? Changiing coupling does not tell a lot in this situation.

I'm glad I found this video. Though I got lost after 6.:30. Can oscilloscope also affect the voltage? Or does it only "see" and show the current/voltage as is and all the buttons are just to make it fit the screen? I'm considering to buy an osciloscope (currently just have a multimeter) but I'm bit too poor and too "scared". These aren't cheep toys.

@w2aew

3 жыл бұрын

The scope only sees the voltage, it doesn't affect it (ideally). It is true that the resistive and capacitive loading of a scope probe can affect some circuits. But, usually you'd consider a scope as a "monitor" and not an active part of the circuit.

@madyogi6164

3 жыл бұрын

@@w2aew Thank you! Glad to know

w2aew, when the AC voltages on TV circuits and Arcade games are reversed polarity the display images fonts and images will have a "wavey" look. From 12VAC, 7VAC, 5VAC if the AC voltages are reversed polarity out of phase the image fonts and images are wavey, Any reasons why? How can I use a DMM meter to know if my VAC voltages are In phase or out of phase, how can I know using a DMM meter set to measure AC voltages?

I'm wondering if you could do a video on pros/cons of connecting up different components in series vs. parallel. E g. Signal gen is your source. You want to see output on 1. Freq counter, 2. VOM, 3. Oscilloscope all simultaneously. So do you connect all three in series i.e. (daisy chained?) Or, feed all three in parallel from a three-way splitter from the sig gen(?)

@w2aew

2 жыл бұрын

Note that even when you connect your counter, scope, etc. to each other using things like BNC-tee connections, they are still in PARALLEL with the signal source and load - they are not in series. When your signal frequencies are low (below about 1MHz, and definitely below 100kHz), the way you connect won't really have an affect. When you go higher in frequency, where transmission line effects start being important (above 1-10MHz or so), then it does matter. You can use BNC-tee connections, but mount the Tee(s) directly at the instrument connector (no coax) so that the stub length of the connection from the main line to the instrument is as short as possible. You can get away with this up to a few hundred MHz. Above that, then everything needs a proper termination and the splitter is the way to go.

@mikem5043

2 жыл бұрын

@@w2aew Ok thanks I think I see what you mean.

Hi, I am a bit confused. When in AC coupling mode, should'nt the DC get blocked? So when you switched to AC mode, how come you are seeing it ride on the DC? Sorry if this is a dumb question.

@w2aew

7 жыл бұрын

When switched to AC coupling, the DC offset observed on the scope is simply due to the Vertical Position knob on the scope.

@skilambi

7 жыл бұрын

oh i see...thanks for the reply. Really liked the video. Learnt alot.

Off topic, but I've got a question about impedance matching. For maximum power transfer, the impedances of the source, transmission lines, and load have to match. But does the source impedance have to match in order to avoid return loss/reflections? A 25Ω source into a 50Ω load leaves power on the table, but will any power reflect back to the source in an arrangement where there is no (or electrically short) transmission line, or the transmission line and load are matched (but again, not to the source)? My intuition thus far says that it shouldn't matter, with power supplies and audio amps being examples, but I wanted to know for sure by asking someone much more experienced than I am, especially where RF is concerned.

@w2aew

Жыл бұрын

The source impedance will not affect return loss or reflections at the load end. If the load is matched to the transmission line, there will be little/no reflection, and the source impedance won't matter.

@RAndrewNeal

Жыл бұрын

@@w2aew Thanks for helping me out, and confirming my intuition! I appreciate that you still reply to comments on these old videos to help out relatively inexperienced guys like myself. God bless!

does the a/c coupling setting on scope essentially add a capacitor to the circuit to further reduce dc ripple? thanks john

@w2aew

4 жыл бұрын

No, it doesn't. AC coupling inserts a capacitor in *series* with the signal in order to remove the DC component so that only the AC portion of the signal is displayed on the scope.

Does analog Oscopes have a Persistence time adjustment? and what signals when measuring would you want to use the Persistence time? I know its used to measure AM modulation signals on digital Oscopes but most Analog Oscopes didn't have a persistence time adjustment so I don't know how they were measuring AM modulation waveform without the persistence time adjustment like on digital Oscopes

@w2aew

3 жыл бұрын

Only a very few specialized analog scopes had variable persistence phosphor. The vast majority of analog scope do not have variable persistence. You don't need a persistence adjustment on an analog scope to view/measure AM signals

@waynegram8907

3 жыл бұрын

@@w2aew But what was the persistence adjustment on analog scoped used for to measure what types of waveforms and signals?

@w2aew

3 жыл бұрын

@@waynegram8907 On those rare scopes that had a persistence adjustment, it was used for waveform storage so that you could examine signal-shot or rare events. It was the pre-cursor to digital storage scopes.

@waynegram8907

3 жыл бұрын

@@w2aew but what is the persistence time used for on digital oscopes to measure what type of waveforms and signals? the persistence time on digital oscopes is 250ms, 500ms, 1second, 2second, 5 second, I don't know what these are used for. Is the persistence time used for trying to look for "glitches"?

@w2aew

3 жыл бұрын

@@waynegram8907 Mainly, yes.

I don't really understand why there is AC/DC coupling on the channel and the trig section too.

@w2aew

9 жыл бұрын

Check out my video #11 on the triggering controls and their usage. Www.kzread.info/dash/bejne/gXp7z4-Jlc-aeMo.html

@bmwm3cs

9 жыл бұрын

Great Vid, I watched it and learned a lot. Thank You! However, I am not quite sure what would happen if you DC coupled the trig with an AC coupled channel. Why application could I use that for?

@w2aew

9 жыл бұрын

I'm sure that this combination might come in handy for some applications, but probably not very often.

Ghost voltages are due to wires coupling or other interferences in the circuit. My question is how do you know when you're measuring a ghost voltage or how do you even know if you have a ghost voltage? Can the oscilloscope determine a real voltage from a ghost voltage?

@w2aew

5 жыл бұрын

If you load the circuit, a ghost voltage will go away. This is the principle behind the classic "Wiggy" tester.

I have one question sir. Why the half wave got shifted to the negative side from 0 level voltage (@2:20)? Even if we consider around 1 volt drop across diode, should it be appearing above the 0 volt level ? If it is shifting to downwards, does that mean diode is conducting for that small fraction of voltage with opposite polarity? Where did I go wrong? Please help me.

@w2aew

Жыл бұрын

Because the scope was AC coupled, so the signal settled around it's average value.

@deepakjanardhanan7394

Жыл бұрын

@@w2aew yayyy I got the reply...Thank you sir for replying 😊🙏🙏🙏✌️. So the initial level we are setting is not "zero" level it is better to say the "average" level. Am I correct sir??

@w2aew

Жыл бұрын

@@deepakjanardhanan7394 When using AC coupling, yes.

@deepakjanardhanan7394

Жыл бұрын

@@w2aew Thank you sir 🙏🙏😊.

Nice Tek scopes? Which all do you have?

@w2aew

10 жыл бұрын

I've got a 465B, 485, 2465 and 2467. Most came to me in some need of repair...

When measuring AC 60hz how can you measure how many zero crossing events happen in one second using an Oscilloscope? its suppose to have 120 zero crossing events but how do you view this on an Oscilloscope

@w2aew

3 жыл бұрын

If you set the scope to 100ms/div, then you'll have 1 second of time across the screen - then pause the scope and count the cycles - you should see 60 cycles, and since you have two zero-crossings per cycle, there's your 120 zero-crossing events.

@waynegram8907

3 жыл бұрын

@@w2aew Does Digital Oscilloscopes have an Event List or a Menu to display all the zero crossing events?

@w2aew

3 жыл бұрын

@@waynegram8907 Some do, some don't.

@waynegram8907

3 жыл бұрын

@@w2aew Can you make a video showing how to set up the event listing to list all the zero crossing events because you have to set the upper level and lower level window of the events

AC/DC coupling is done by caps, this is to my understanding ?

@w2aew

8 жыл бұрын

+jon123423 Yes - AC coupling inserts a capacitor in series between the front panel connector and the scope input.

what causes a circuit to have ghost voltages? what do you mean by this wiggy tester? How would an electronic technician know if the voltage is real or a ghost voltage, how can you tell the differences?

@w2aew

5 жыл бұрын

A ghost voltage is simply a voltage that is picked up on a high-impedance line due to coupling through the air to some other power source (like an antenna). As soon as a load is placed on this ghost voltage, it will collapse. The Wiggy tester uses a solenoid as a load on the AC line so that ghost voltages won't be seen. Here's an example of a Wiggy: www.amazon.com/Square-D-WIGGY-VOLTAGE-TESTER/dp/B000BVXW1C

you have a lot of scopes.

You are The Godfather of cool. Gratitude++ 99e99

Transitors, who needs them! Try out androidcircuitsolver on google