Dragging the Tamiya F-4B through the suck zone between finishing up construction and being ready for paint.
Жүктеу.....
Пікірлер: 22
@MikeCederberg8 ай бұрын
Matthew…. Watching your vids on the 1/48 Tamiya Phantom II. Twice - yes twice, I almost spewed a (shut up compressor) mouthful of coffee all over my tablet because of your comments during the building. I’ve been building for years and Admin a number of the ‘original’ modelling fb groups! You sir, are a hoot! (I just ordered TWO Glue Dot dispensers). Even my bride walks into the room and asks, “Is that the ‘shut up compressor’ guy?” You’re famous - in my house - buddy!!!
@WhiteGloveModels2 жыл бұрын
I always learn something new every time I watch one of your videos. Thanks for sharing. The Phantom is looking awesome. I'm always fearful of messing with Canopies, but will definitely have to give your technique a try.
@jcwoodman52852 жыл бұрын
Very nice!🤗
@nigelsmith73662 жыл бұрын
I too hate scribing/rescribing so have started to pre scribe some panel lines before construction.... While removing sprue location marks and seam lines I go over any panel lines that go across joints... That way when you go to clean up the seam you can restore the line easier
@Gabriel4Drummer2 жыл бұрын
Nice tip about transparent paint, thanks!
@laMoort2 жыл бұрын
the meditation that is canopy polishing. was a great episode to watch all the way! otoh i wish somebody could come up with a proper solution for the inherent refraction of them translucent parts like armored glass, sights, canopies and projectors for hud etc...
@laurentlachand81022 жыл бұрын
Just waouuu amazing job thank for so many tips 🙏
@LagoAZ2 жыл бұрын
10/10 video. 10/10 cursing. Take that Karens.
@PhuVet2 жыл бұрын
You ever try microbrushes? You can get a ton cheap on ebay. You hit details and after pull the brush point off and use it to apply CA.
@user-fo6ud3zs2o2 жыл бұрын
красиво,аккуратно работаете...
@PhuVet2 жыл бұрын
Alclad armored glass is great for the windscreen.
@alphamercstudios2 жыл бұрын
16:16 you know they make good models when they refer an old damaged brush as fluffy f***ers, can I use that term?
@johndillon80512 жыл бұрын
I noticed in this episode that I was holding my breath while you did some fine detail painting, just as I would if I were doing it. I bet I've been doing it with all of your videos. Force of habit?
@egyeneskifli78082 жыл бұрын
About the focusing issues: wouldn't it be better to use a smaller aperture to widen the DoF? I don't know what kind of photo gear you use, and in what kind of setup.
@PCDan2 жыл бұрын
4/2/22 and where are you? 😊
@stevelagrutta5005 Жыл бұрын
I don’t see any of the modeler’s prime all the parts on the spru. Is that not a good idea?
@mostlycloudy30692 жыл бұрын
this is why you are the BIG DOOG.
@lucasner4632 жыл бұрын
Sorry to be "that" guy with a pedantic question...but whose black CA do you use? Is it one of the rubberized glues?
@DoogsModels
2 жыл бұрын
Ammo
@ChristianGurney
2 жыл бұрын
I had the same question, so thanks for asking first.
@paulhargreaves14972 жыл бұрын
I think we need a Ukrainian air force model soon Doog! Please.........
@MightyCrazy2 жыл бұрын
All Doogs does is complain. Like he is on a rag 24/7. Never happy just nagging nonstop.
Пікірлер: 22
Matthew…. Watching your vids on the 1/48 Tamiya Phantom II. Twice - yes twice, I almost spewed a (shut up compressor) mouthful of coffee all over my tablet because of your comments during the building. I’ve been building for years and Admin a number of the ‘original’ modelling fb groups! You sir, are a hoot! (I just ordered TWO Glue Dot dispensers). Even my bride walks into the room and asks, “Is that the ‘shut up compressor’ guy?” You’re famous - in my house - buddy!!!
I always learn something new every time I watch one of your videos. Thanks for sharing. The Phantom is looking awesome. I'm always fearful of messing with Canopies, but will definitely have to give your technique a try.
Very nice!🤗
I too hate scribing/rescribing so have started to pre scribe some panel lines before construction.... While removing sprue location marks and seam lines I go over any panel lines that go across joints... That way when you go to clean up the seam you can restore the line easier
Nice tip about transparent paint, thanks!
the meditation that is canopy polishing. was a great episode to watch all the way! otoh i wish somebody could come up with a proper solution for the inherent refraction of them translucent parts like armored glass, sights, canopies and projectors for hud etc...
Just waouuu amazing job thank for so many tips 🙏
10/10 video. 10/10 cursing. Take that Karens.
You ever try microbrushes? You can get a ton cheap on ebay. You hit details and after pull the brush point off and use it to apply CA.
красиво,аккуратно работаете...
Alclad armored glass is great for the windscreen.
16:16 you know they make good models when they refer an old damaged brush as fluffy f***ers, can I use that term?
I noticed in this episode that I was holding my breath while you did some fine detail painting, just as I would if I were doing it. I bet I've been doing it with all of your videos. Force of habit?
About the focusing issues: wouldn't it be better to use a smaller aperture to widen the DoF? I don't know what kind of photo gear you use, and in what kind of setup.
4/2/22 and where are you? 😊
I don’t see any of the modeler’s prime all the parts on the spru. Is that not a good idea?
this is why you are the BIG DOOG.
Sorry to be "that" guy with a pedantic question...but whose black CA do you use? Is it one of the rubberized glues?
@DoogsModels
2 жыл бұрын
Ammo
@ChristianGurney
2 жыл бұрын
I had the same question, so thanks for asking first.
I think we need a Ukrainian air force model soon Doog! Please.........
All Doogs does is complain. Like he is on a rag 24/7. Never happy just nagging nonstop.