Where does 1.414 come from and why is it used with 45º offsets?
Жүктеу.....
Пікірлер: 12
@07slowbalt10 ай бұрын
Great this made me even more confused!
@ahmadfarooque4971 Жыл бұрын
Thank you sir
@adamm40546 жыл бұрын
But what would it be for metric?
@uhpprocesspipinginc5973
6 жыл бұрын
It is the same for both imperial or metric systems since the relationship between sides of the triangle are presented as a ratio (unitless)
@fleuryelite21702 жыл бұрын
What If your looking for the travel with a fittin that goes from 45 to 90 or 45 to tee
@uhpprocesspipinginc5973
2 жыл бұрын
The same procedure can be used. The travel in each case (with all SET values being equal) will be the same. We are still using a 45° fitting to start the offset. The difference will be the pipe cut length between the fittings which is dependent on the takeout of both fittings. TL = CL + (F1TO + F2TO) WHERE: TL = TRAVEL LENGTH CL = CUT LENGTH F1TO = FITTING 1 TAKEOUT (45 elbow) F2TO = FITTING 2 TAKEOUT (90 elbow or TEE)
@avneetmann523510 ай бұрын
So hypothetically if we have an offset angle of 67.5 could we multiply by 1.207? (.414\2)
@uhpprocesspipinginc5973
10 ай бұрын
The calculation shown (where the run and set are equal ) only applies to a 45 degree offset -for other offset angles, the run and set are not equal. You can calculate travel factors or use a table of tangents for other offset angles.
@hubby93457 ай бұрын
Little confusing
@leonwoods40527 ай бұрын
OK 1.414 /2😂 some illustrations would be awesome don't you think. 😂😂😂😂😂😂😅
@uhpprocesspipinginc5973
7 ай бұрын
Not sure how additional illustrations would help unless you mean to include specific example numbers. All content in the video created by UHP - not borrowed from a book.
@leonwoods40527 ай бұрын
Where is the Math ? Basically this video is a manual out of a book.show the work SIR........
Пікірлер: 12
Great this made me even more confused!
Thank you sir
But what would it be for metric?
@uhpprocesspipinginc5973
6 жыл бұрын
It is the same for both imperial or metric systems since the relationship between sides of the triangle are presented as a ratio (unitless)
What If your looking for the travel with a fittin that goes from 45 to 90 or 45 to tee
@uhpprocesspipinginc5973
2 жыл бұрын
The same procedure can be used. The travel in each case (with all SET values being equal) will be the same. We are still using a 45° fitting to start the offset. The difference will be the pipe cut length between the fittings which is dependent on the takeout of both fittings. TL = CL + (F1TO + F2TO) WHERE: TL = TRAVEL LENGTH CL = CUT LENGTH F1TO = FITTING 1 TAKEOUT (45 elbow) F2TO = FITTING 2 TAKEOUT (90 elbow or TEE)
So hypothetically if we have an offset angle of 67.5 could we multiply by 1.207? (.414\2)
@uhpprocesspipinginc5973
10 ай бұрын
The calculation shown (where the run and set are equal ) only applies to a 45 degree offset -for other offset angles, the run and set are not equal. You can calculate travel factors or use a table of tangents for other offset angles.
Little confusing
OK 1.414 /2😂 some illustrations would be awesome don't you think. 😂😂😂😂😂😂😅
@uhpprocesspipinginc5973
7 ай бұрын
Not sure how additional illustrations would help unless you mean to include specific example numbers. All content in the video created by UHP - not borrowed from a book.
Where is the Math ? Basically this video is a manual out of a book.show the work SIR........